Nissan March K13. Instruction — part 229
ACCELERATOR PEDAL RELEASED POSITION LEARNING
EC-377
< BASIC INSPECTION >
[HR12DE (TYPE 2)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
ACCELERATOR PEDAL RELEASED POSITION LEARNING
Description
INFOID:0000000006036894
Accelerator Pedal Released Position Learning is a function of ECM to learn the fully released position of the
accelerator pedal by monitoring the accelerator pedal position sensor output signal. It must be performed each
time harness connector of accelerator pedal position sensor or ECM is disconnected.
Work Procedure
INFOID:0000000006036895
1.
START
1.
Make sure that accelerator pedal is fully released.
2.
Turn ignition switch ON and wait at least 2 seconds.
3.
Turn ignition switch OFF and wait at least 10 seconds.
4.
Turn ignition switch ON and wait at least 2 seconds.
5.
Turn ignition switch OFF and wait at least 10 seconds.
>> END
EC-378
< BASIC INSPECTION >
[HR12DE (TYPE 2)]
THROTTLE VALVE CLOSED POSITION LEARNING
THROTTLE VALVE CLOSED POSITION LEARNING
Description
INFOID:0000000006036896
Throttle Valve Closed Position Learning is a function of ECM to learn the fully closed position of the throttle
valve by monitoring the throttle position sensor output signal. It must be performed each time harness connec-
tor of electric throttle control actuator or ECM is disconnected.
Work Procedure
INFOID:0000000006036897
1.
START
1.
Make sure that accelerator pedal is fully released.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
Make sure that throttle valve moves during above 10 seconds by confirming the operating sound.
>> END
IDLE AIR VOLUME LEARNING
EC-379
< BASIC INSPECTION >
[HR12DE (TYPE 2)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
IDLE AIR VOLUME LEARNING
Description
INFOID:0000000006036898
Idle Air Volume Learning is a function of ECM to learn the idle air volume that keeps each engine idle speed
within the specific range. It must be performed under any of the following conditions:
• Each time electric throttle control actuator or ECM is replaced.
• Idle speed or ignition timing is out of specification.
Work Procedure
INFOID:0000000006036899
1.
PRECONDITIONING
Make sure that all of the following conditions are satisfied.
Learning will be cancelled if any of the following conditions are missed for even a moment.
• Battery voltage: More than 12.9 V (At idle)
• Engine coolant temperature: 70 - 100
°
C (158 - 212
°
F)
• Shift lever: P or N (A/T), Neutral (M/T)
• Electric load switch: OFF
(Air conditioner, headlamp, rear window defogger)
• Steering wheel: Neutral (Straight-ahead position) position
• Vehicle speed: Stopped
• Transmission: Warmed-up
- A/T models
• With CONSULT-III: Drive vehicle until “ATF TEMP SE 1” in “DATA MONITOR” mode of “A/T” system indi-
cates less than 0.9V.
• Without CONSULT-III: Drive vehicle for 10 minutes.
- M/T models
• Drive vehicle for 10 minutes.
Do you have CONSULT-III?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
IDLE AIR VOLUME LEARNING
With CONSULT-III
1.
Perform ACCELERATOR PEDAL RELEASED POSITION LEARNING. Refer to
2.
Perform THROTTLE VALVE CLOSED POSITION LEARNING. Refer to
.
3.
Start engine and warm it up to normal operating temperature.
4.
Select “IDLE AIR VOL LEARN” in “WORK SUPPORT” mode with CONSULT-III.
5.
Touch “START” and wait 20 seconds.
Is “CMPLT” displayed on CONSULT-III screen?
YES
>> GO TO 4.
NO
>> GO TO 5.
3.
IDLE AIR VOLUME LEARNING
Without CONSULT-III
NOTE:
• It is better to count the time accurately with a clock.
• It is impossible to switch the diagnostic mode when an accelerator pedal position sensor circuit has
a malfunction.
1.
Perform ACCELERATOR PEDAL RELEASED POSITION LEARNING. Refer to
2.
Perform THROTTLE VALVE CLOSED POSITION LEARNING. Refer to
.
3.
Start engine and warm it up to normal operating temperature.
4.
Turn ignition switch OFF and wait at least 10 seconds.
5.
Confirm that accelerator pedal is fully released, turn ignition switch ON and wait 3 seconds.
6.
Repeat the following procedure quickly five times within 5 seconds.
-
Fully depress the accelerator pedal.
-
Fully release the accelerator pedal.
EC-380
< BASIC INSPECTION >
[HR12DE (TYPE 2)]
IDLE AIR VOLUME LEARNING
7.
Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds until the MIL stops
blinking and turned ON.
8.
Fully release the accelerator pedal within 3 seconds after the MIL turned ON.
9.
Start engine and let it idle.
10. Wait 20 seconds.
>> GO TO 4.
4.
CHECK IDLE SPEED AND IGNITION TIMING
Rev up the engine two or three times and make sure that idle speed and ignition timing are within the specifi-
cations.
For specification, refer to
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 5.
5.
DETECT MALFUNCTIONING PART
Check the following
• Check that throttle valve is fully closed.
• Check PCV valve operation.
• Check that downstream of throttle valve is free from air leakage.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace malfunctioning part.
6.
DETECT MALFUNCTIONING PART
Engine component parts and their installation condition are questionable. Check and eliminate the cause of
the incident.
It is useful to perform “TROUBLE DIAGNOSIS - SPECIFICATION VALUE”. Refer to
If any of the following conditions occur after the engine has started, eliminate the cause of the incident and
perform Idle Air Volume Learning all over again:
• Engine stalls.
• Erroneous idle.
>> INSPECTION END
PBIB0665E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст