Nissan March K13. Instruction — part 142
COMPONENT PARTS
EC-29
< SYSTEM DESCRIPTION >
[HR12DE (TYPE 1)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Refrigerant Pressure Sensor
INFOID:0000000005991062
The refrigerant pressure sensor is installed at the condenser of the air conditioner system. The sensor uses an
electrostatic volume pressure transducer to convert refrigerant pressure to voltage. The voltage signal is sent
to ECM, and ECM controls cooling fan system.
Stop Lamp Switch
INFOID:0000000005991063
Brake switch signal is applied to the ECM through the stop lamp
switch when the brake pedal is depressed. This signal is used
mainly to decrease the engine speed when the vehicle is being
driven.
PBIB2657E
JSBIA0308ZZ
EC-30
< SYSTEM DESCRIPTION >
[HR12DE (TYPE 1)]
SYSTEM
SYSTEM
ENGINE CONTROL SYSTEM
ENGINE CONTROL SYSTEM : System Diagram
INFOID:0000000005995397
NOTE:
• Engine oil temperature sensor is not used for engine control system.
• Battery temperature sensor is not used for engine control system.
JPBIA3237GB
SYSTEM
EC-31
< SYSTEM DESCRIPTION >
[HR12DE (TYPE 1)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
ENGINE CONTROL SYSTEM : System Description
INFOID:0000000005995398
ECM performs various controls such as fuel injection control and ignition timing control.
ENGINE CONTROL SYSTEM : Fail Safe
INFOID:0000000005995478
NON DTC RELATED ITEM
DTC RELATED ITEM
Detected
items
Engine operating condition
in fail-safe mode
Remarks
Reference page
Malfunction
indicator
lamp circuit
Engine speed will not rise
more than 2,500 rpm due
to the fuel cut
When there is an open circuit on MIL circuit, the ECM cannot warn the
driver by lighting up MIL when there is malfunction on engine control
system.
Therefore, when electrical controlled throttle and part of ECM related
diagnoses are continuously detected as NG for 5 trips, ECM warns the
driver that engine control system malfunctions and MIL circuit is open
by means of operating fail safe function.
The fail safe function also operates when above diagnoses except MIL
circuit are detected and demands the driver to repair the malfunction.
DTC No.
Detected items
Engine operating condition in fail safe mode
P0011
Intake valve timing control
The signal is not energized to the intake valve timing control solenoid valve and the valve
control does not function.
P0102
P0103
Mass air flow sensor circuit
Engine speed will not rise more than 2,400 rpm due to the fuel cut.
P0117
P0118
Engine coolant tempera-
ture sensor circuit
Engine coolant temperature will be determined by ECM based on the following conditions.
CONSULT-III displays the engine coolant temperature decided by ECM.
Condition
Engine coolant temperature decided
(CONSULT-III display)
Just as ignition switch is turned ON
or START
40
°
C (104
°
F)
Approx. 4 minutes or more after
engine starting
80
°
C (176
°
F)
Except as shown above
40 - 80
°
C (104 - 176
°
F)
(Depends on the time)
When the fail safe system for engine coolant temperature sensor is activated, the cooling
fan operates while engine is running.
P0122
P0123
P0222
P0223
P2135
Throttle position sensor
The ECM controls the electric throttle control actuator in regulating the throttle opening in
order for the idle position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal
condition.
So, the acceleration will be poor.
P0403
EGR volume control valve
Engine speed will not rise more than 2,400 rpm due to the fuel cut.
P0605
ECM
(When ECM calculation function is malfunctioning:)
ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
P0643
Sensor power supply
ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
P1805
Brake switch
ECM controls the electric throttle control actuator by regulating the throttle opening to a
small range.
Therefore, acceleration will be poor.
Vehicle condition
Driving condition
When engine is idling
Normal
When accelerating
Poor acceleration
EC-32
< SYSTEM DESCRIPTION >
[HR12DE (TYPE 1)]
SYSTEM
MULTIPORT FUEL INJECTION SYSTEM
MULTIPORT FUEL INJECTION SYSTEM : System Diagram
INFOID:0000000005995400
P2100
P2103
Throttle control motor relay
ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
P2101
Electric throttle control
function
ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
P2118
Throttle control motor
ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
P2119
Electric throttle control ac-
tuator
(When electric throttle control actuator does not function properly due to the return spring
malfunction:)
ECM controls the electric throttle actuator by regulating the throttle opening around the
idle position. The engine speed will not rise more than 2,000 rpm.
(When throttle valve opening angle in fail safe mode is not in specified range:)
ECM controls the electric throttle control actuator by regulating the throttle opening to 20
degrees or less.
(When ECM detects the throttle valve is stuck open:)
While the vehicle is driving, it slows down gradually by fuel cut. After the vehicle stops, the
engine stalls.
The engine can restart in the Neutral position, and engine speed will not exceed 1,000 rpm
or more.
P2122
P2123
P2127
P2128
P2138
Accelerator pedal position
sensor
The ECM controls the electric throttle control actuator in regulating the throttle opening in
order for the idle position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal
condition.
So, the acceleration will be poor.
DTC No.
Detected items
Engine operating condition in fail safe mode
JSBIA0317GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст