Nissan March K13. Instruction — part 337
FSU-12
< REMOVAL AND INSTALLATION >
TRANSVERSE LINK
TRANSVERSE LINK
Exploded View
INFOID:0000000006046093
Removal and Installation
INFOID:0000000006046094
REMOVAL
1.
Remove tires. Refer to
XX-XX, "*****"
.
2.
Remove lock plate from strut assembly. Refer to
Dummy cross-reference("XX-XX")
.
3.
Remove strut mounting bolts and nuts from steering knuckle. Refer to
Dummy cross-reference("XX-XX")
.
4.
Remove transverse link from steering knuckle.
5.
Remove transverse link from suspension member.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of bolts and nuts at the front suspension member, under unladen conditions with
tires on level ground.
Inspection
INFOID:0000000006046095
INSPECTION AFTER REMOVAL
Check the following items, and replace the parts if necessary.
Transverse Link
• Transverse link and bushing for deformation, cracks or damage.
• Ball joint boot for cracks or other damage, and also for grease leakage.
Swing Torque
1.
Instructionly move ball stud to confirm it moves smoothly with no binding.
2.
Move ball stud at least ten times by hand to check for smooth movement.
1.
Front suspension member
2.
Transverse link
Refer to
XX-XX, "*****"
for symbols in the figure.
JPEIA0227GB
TRANSVERSE LINK
FSU-13
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
3.
Hook a spring balance (A) at cutout on ball stud (B). Confirm
spring balance measurement value is within specifications when
ball stud begins moving.
• If swing torque exceeds standard range, replace transverse link
assembly.
Axial End Play
1.
Move ball stud at least ten times by hand to check for smooth movement.
2.
Move tip of ball stud in axial direction to check for looseness.
• If axial end play exceeds the standard value, replace transverse link assembly.
INSPECTION AFTER INSTALLATION
1.
Check wheel alignment. Refer to
2.
Adjust neutral position of steering angle sensor. Refer to
XX-XX, "*****"
.
Swing torque
: Refer to
Measurement on
spring balance
: Refer to
JPEIA0138ZZ
Axial end play
: Refer to
FSU-14
< REMOVAL AND INSTALLATION >
FRONT SUSPENSION MEMBER
FRONT SUSPENSION MEMBER
Exploded View
INFOID:0000000006046458
Removal and Installation
INFOID:0000000006046100
REMOVAL
1.
Remove tires. Refer to
XX-XX, "*****"
.
2.
Remove transverse link. Refer to
XX-XX, "*****"
.
3.
Remove steering outer socket from steering knuckle. Refer to
XX-XX, "*****"
.
4.
Remove intermediate shaft from steering gear assembly. Refer to
XX-XX, "*****"
.
5.
Remove rear torque rod. Refer to
XX-XX, "*****"
.
6.
Set suitable jack under front suspension member.
CAUTION:
Check the stable condition when using a jack.
7.
Remove suspension member mounting bolts.
8.
Gradually lower the jack to remove front suspension member from vehicle body.
CAUTION:
Check the stable condition when using a jack.
9.
Remove steering gear assembly from suspension member. Refer to
XX-XX, "*****"
.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of bolts and nuts, under unladen conditions with tires on level ground.
Inspection
INFOID:0000000006046101
INSPECTION AFTER DISASSEMBLY
Check front suspension member for cracks, wear or damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel alignment. Refer to
.
2.
Adjust neutral position of steering angle sensor. Refer to
XX-XX, "*****"
.
1.
Front suspension member
2.
Transverse link
Refer to
XX-XX, "*****"
for symbols in the figure.
JPEIA0227GB
SERVICE DATA AND SPECIFICATIONS (SDS)
FSU-15
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Alignment
INFOID:0000000006046102
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Ball Joint
INFOID:0000000006046103
Wheelarch Height
INFOID:0000000006046457
Item
Standard
Camber
Degree minute (Decimal degree)
Minimum
−
0
°
50
′
(
−
0.83
°
)
Nominal
−
0
°
05
′
(
−
0.08
°
)
Maximum
0
°
40
′
(0.66
°
)
Left and right difference
0
°
45
′
(0.75
°
)
Caster
Degree minute (Decimal degree)
Minimum
2
°
50
′
(2.84
°
)
Nominal
3
°
35
′
(3.58
°
)
Maximum
4
°
20
′
(4.33
°
)
Left and right difference
0
°
45
′
(0.75
°
)
Kingpin inclination
Degree minute (Decimal degree)
Minimum
11
°
00
′
(11.00
°
)
Nominal
11
°
45
′
(11.75
°
)
Maximum
12
°
30
′
(12.50
°
)
Toe-in
Total toe-in
Distance
Minimum
0 mm (0 in)
Nominal
In 1.0 mm (0.05 in)
Maximum
In 2.0 mm (0.07 in)
Toe angle (left wheel or right wheel)
Degree minute (Decimal degree)
Minimum
0
°
00
′
(0.00
°
)
Nominal
In 0
°
05
′
(0.08
°
)
Maximum
In 0
°
10
′
(0.16
°
)
Item
Standard
Swing torque
0.5 – 4.9 N·m (0.05 – 0.5 kg-m, 5 – 43 in-lb)
Measurement on spring balance
15.4 – 150.8 N (1.6 – 15.4 kg, 3.6 – 33.9 lb)
Axial end play
0 mm (0 in)
Item
Standard
Tire size
165/70R14
175/60R15
Front (Hf)
659 mm (25.94 in)
661 mm (26.02 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст