Nissan March K13. Instruction — part 408
INL-12
< SYSTEM DESCRIPTION >
SYSTEM
• Combination meter illuminates the meter illumination according to position light request signal.
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
INL-13
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)
INFOID:0000000006067177
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
*: This item is displayed, but is not used.
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT-III.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion instruction.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
Automatic air conditioner
AIR CONDITONER
×
×
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NATS
IMMU
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door
TRUNK
×
—
THEFT ALM*
×
×
×
—
RETAINED PWR*
×
Signal buffer system
SIGNAL BUFFER
×
×
I N L - 1 4
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
INT LAMP
CONSULT screen item
Indication/Unit
Description
Vehicle Speed
km/h
Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter
km
Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition
SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “LOCK”)
SLEEP>OFF
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “OFF”.)
LOCK>ACC
While turning power supply position from “LOCK” to “ACC”
ACC>ON
While turning power supply position from “ACC” to “IGN”
RUN>ACC
While turning power supply position from “RUN” to “ACC” (Vehicle
is stopping and selector lever is except P position.)
CRANK>RUN
While turning power supply position from “CRANKING” to “RUN”
(From cranking up the engine to run it)
RUN>URGENT
While turning power supply position from “RUN“ to “ACC” (Emer-
gency stop operation)
ACC>OFF
While turning power supply position from “ACC” to “OFF”
OFF>LOCK
While turning power supply position from “OFF” to “LOCK”
OFF>ACC
While turning power supply position from “OFF” to “ACC”
ON>CRANK
While turning power supply position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “OFF”.) to low power consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “LOCK”.) to low power consumption mode
LOCK
Power supply position is “LOCK” (Ignition switch OFF with steer-
ing is locked.)
OFF
Power supply position is “OFF” (Ignition switch OFF with steering
is unlocked.)
ACC
Power supply position is “ACC” (Ignition switch ACC)
ON
Power supply position is “IGN” (Ignition switch ON with engine
stopped)
ENGINE RUN
Power supply position is “RUN” (Ignition switch ON with engine
running)
CRANKING
Power supply position is “CRANKING” (At engine cranking)
IGN Counter
0 - 39
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→
2
→
3...38
→
39 after returning to the normal condition
whenever ignition switch OFF
→
ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
INL-15
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
INT LAMP : CONSULT-III Function (BCM - INT LAMP)
INFOID:0000000006030904
WORK SUPPORT
*: Factory setting
DATA MONITOR
JPLIA0093GB
Service item
Setting item
Setting
ROOM LAMP TIMER SET
MODE 2
7.5 sec.
Sets the interior room lamp ON time. (Timer operating time)
MODE 3*
15 sec.
MODE 4
30 sec.
SET I/L D-UNLCK INTCON
On*
With the interior room lamp timer function
Off
Without the interior room lamp timer function
ROOM LAMP ON TIME SET
MODE 1
0.5 sec.
Sets the interior room lamp gradual brightening time.
MODE 2*
1 sec.
MODE 3
2 sec.
MODE 4
3 sec.
MODE 5
0 sec.
ROOM LAMP OFF TIME SET
MODE 1
0.5 sec.
Sets the interior room lamp gradual dimming time.
MODE 2*
1 sec.
MODE 3
2 sec.
MODE 4
3 sec.
MODE 5
0 sec.
R LAMP TIMER LOGIC SET
MODE 1*
Interior room lamp timer activates with synchronizing all doors.
MODE 2
Interior room lamp timer activates with synchronizing the driver door
only.
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
The switch status input from request switch (driver side)
REQ SW-AS
[On/Off]
The switch status input from request switch (passenger side)
REQ SW-RR
[On/Off]
NOTE:
The item is indicated, but not monitored.
REQ SW-RL
[On/Off]
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст