Nissan March K13. Instruction — part 658
SERVICE DATA AND SPECIFICATIONS (SDS)
TM-49
< SERVICE DATA AND SPECIFICATIONS (SDS)
[5MT: RS5F91R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000006056595
Transaxle type
RS5F91R
Engine type
HR12DE
Model code number
1HC0C
1HC0A
Number of speed
5
Synchromesh type
Warner
Shift pattern
Gear ratio
1st
3.7273
2nd
2.0476
3rd
1.3929
4th
1.0294
5th
0.8205
Reverse
3.5454
Final gear
4.0667
4.5000
Number of teeth
Input gear
1st
11
2nd
21
3rd
28
4th
34
5th
39
Reverse
11
Main gear
1st
41
2nd
43
3rd
39
4th
35
5th
32
Reverse
39
Reverse idler gear
26
Final gear
Final gear/Pinion
61/15
63/14
Side gear/Pinion
mate gear
13/9
Oil capacity (Reference)
(Imp pt)
Approx. 2.6 (4-5/8)
SCIA0821E
VTL-1
VENTILATION, HEATER & AIR CONDITIONER
C
D
E
F
G
H
J
K
L
M
SECTION
VTL
A
B
VTL
N
O
P
CONTENTS
VENTILATION SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution Necessary for Steering Wheel Rota-
tion after Battery Disconnect . . . . . . . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . . ..
SYSTEM DESCRIPTION . . . . . . . ..
VENTILATION SYSTEM . . . . . . . . . .
System Description . . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . .
DUCT AND GRILLE . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . ..
CENTER VENTILATOR GRILLE . . . . . . . ....
CENTER VENTILATOR GRILLE : Removal and
Installation . . . . . . . . . . . . . . . ....
SIDE VENTILATOR GRILLE . . . . . . . . . ..
SIDE VENTILATOR GRILLE : Removal and In-
stallation . . . . . . . . . . . . . . . . ...
CENTER VENTILATOR DUCT . . . . . . . . ...
CENTER VENTILATOR DUCT : Removal and In-
stallation . . . . . . . . . . . . . . . . ...
FOOT DUCT . . . . . . . . . . . . . . . ....
FOOT DUCT : Removal and Installation . . . . ..
BLOWER MOTOR . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
VTL-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006067223
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Instruction.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
INFOID:0000000006067224
NOTE:
• Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
OPERATION PROCEDURE
1.
Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2.
Turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3.
Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4.
Perform the necessary repair operation.
5.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6.
Perform self-diagnosis check of all control units using CONSULT-III.
PREPARATION
VTL-3
< PREPARATION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000006032356
Tool name
Description
Remover tool
Remove clips, pawls, and metal clips
JMKIA3050ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст