Nissan Primera P12. Instruction — part 165
SERVICE DATA AND SPECIFICATIONS (SDS)
CO-21
[YD]
C
D
E
F
G
H
I
J
K
L
M
A
CO
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
Standard and Limit
EBS00SJX
CAPACITY
THERMOSTAT
RADIATOR
Unit: kPa (bar, kg/cm
2
, psi)
Tightening Torque
EBS00SJY
Unit:N·m (kg-m, ft-lb)
Unit:N·m (kg-m, in-lb)*
Engine coolant capacity [With reservoir tank (MAX level)]
9.5
(8-3/8 Imp qt)
Valve opening temperature
80 - 84
°
C (176 - 183
°
F)
Full open lift amount
More than 10 mm/ 95
°
C (0.39 in/203
°
F)
Cap relief pressure
Standard
78 - 98 (0.78 - 0.98, 0.8 - 1.0, 11 - 14)
Limit
59 (0.59, 0.6, 9)
Leakage test pressure
157 (1.57, 1.6, 23)
Radiator mounting bracket
Radiator fan assembly
Radiator fan
Radiator fan motor
3.8 - 4.5 (0.39 - 0.46, 34 - 39)*
3.8 - 4.5 (0.39 - 0.46, 34 - 39)*
2.9 - 3.9 (0.30 - 0.40, 26 - 34)*
4.0 - 4.5 (0.41 - 0.45, 36 - 39)*
Water pump
Water pump pully
Water inlet
Thermostat housing
Water inlet pipe
Hater return pipe
23.0 - 30.0 (2.3 - 3.1, 17 - 22)
7.3 - 9.6 (0.74 - 0.98, 65 - 85)*
21 - 28 (2.1 - 2.9, 16 - 20)
21 - 28 (2.1 - 2.9, 16 - 20)
21 - 28 (2.1 - 2.9, 16 - 20)
21 - 28 (2.1 - 2.9, 16 - 20)
CO-22
[F9Q]
PRECAUTIONS
[F9Q]
PRECAUTIONS
PFP:00001
Precautions For Liquid Gasket
EBS00S34
REMOVAL OF LIQUID GASKET
●
After removing the mounting bolts and nuts, separate the mating
surface using a seal cutter and remove the liquid gasket.
CAUTION:
Be careful not to damage the mating surfaces.
●
In areas where the cutter is difficult to use, use a plastic hammer
to lightly tap the gasket applied area.
CAUTION:
If for some unavoidable reason a tool such as a flat-bladed
screwdriver is used, be careful not to damage the mating
surfaces.
LIQUID GASKET APPLICATION PROCEDURE
1.
Using a scraper, remove the old liquid gasket adhering to the
gasket application surface and the mating surface.
●
Remove the liquid gasket completely from the groove of the
gasket application surface, mounting bolts and bolt holes.
2.
Wipe the gasket application surface and the mating surface with
white gasoline (lighting and heating use) to remove adhering
moisture, grease and foreign materials.
3.
Attach the liquid gasket to the tube presser.
Use Genuine Liquid Gasket or equivalent.
4.
Apply the gasket without breaks to the specified location with the
specified dimensions.
●
If there is a groove for the liquid gasket application, apply the
gasket to the groove.
●
As for the bolt holes, normally apply the gasket inside the
holes. If specified, it should be applied outside the holes.
Make sure to read the instruction in this instruction.
●
Within five minutes of gasket application, install the mating
component.
●
If the liquid gasket protrudes, wipe it off immediately.
●
Do not retighten after the installation.
●
After 30 minutes or more have passed from the installation, fill
the engine oil and coolant.
CAUTION:
If there are instructions in this instruction, observe them.
PBIC0275E
PBIC0003E
EMA0622D
SEM159F
PREPARATION
CO-23
[F9Q]
C
D
E
F
G
H
I
J
K
L
M
A
CO
PREPARATION
PFP:00002
Special Service Tools
EBS00S35
NISSAN tool number
(RENAULT too number)
Tool name
Description
WS39930000
(
—
)
Tube pressure
Pressing the tube of liquid gasket
S-NT052
CO-24
[F9Q]
OVERHEATING CAUSE ANALYSIS
OVERHEATING CAUSE ANALYSIS
PFP:00012
Troubleshooting Chart
EBS00S36
Symptom
Check items
Cooling sys-
tem parts
malfunction
Poor heat transfer
Water pump malfunction
Worn or loose drive belt
—
Thermostat stuck closed
—
Damaged fins
Dust contamination or
paper clogging
Mechanical damage
Clogged radiator cooling
tube
Excess foreign material
(rust, dirt, sand, etc.)
Reduced air flow
Radiator fan does not oper-
ate
—
—
High resistance to fan rota-
tion
Damaged fan blades
Damaged radiator shroud
—
—
—
Improper coolant mixture
ratio
—
—
—
Poor coolant quality
—
—
—
Insufficient coolant
Coolant leaks
Cooling hose
Loose clamp
Cracked hose
Water pump
Poor sealing
Radiator
Cracked radiator tank
Cracked radiator core
Reservoir tank cap
Loose
Poor sealing
Reservoir tank
Cracked reservoir tank
Overflowing reservoir tank
Exhaust gas leaks into
cooling system
Cylinder head deterioration
Cylinder head gasket dete-
rioration
Except cool-
ing system
parts mal-
function
—
Overload on engine
Abusive driving
High engine rpm under no
load
Driving in low gear for
extended time
Driving at extremely high
speed
Powertrain system mal-
function
—
Installed improper size
wheels and tires
Dragging brakes
Improper ignition timing
Blocked or restricted air
flow
Blocked bumper
—
—
Blocked radiator grille
Installed car brassiere
Mud contamination or
paper clogging
Blocked radiator
—
Blocked condenser
—
Installed large fog lamp
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст