Nissan Primera P12. Instruction — part 482
FL-14
FUEL TANK (YD22DDTI)
FUEL TANK (YD22DDTI)
PFP:17202
Removal and Installation
EBS00SIV
REMOVAL
WARNING:
Be sure to read “General Precautions” when working on fuel system. Refer to
.
1.
Disconnect battery ground cable.
2.
Open the fuel filler cap and release the pressure inside the fuel tank.
3.
Remove rear seat bottom.
4.
Peel off floor carpet, then remove inspection hole cover.
5.
Disconnect the harness connector.
6.
Drain fuel from fuel tank if necessary.
PBIC0948E
1.
Fuel filler cap
2.
Grommet
3.
Fuel filler tube
4.
Vent hose
5.
Fuel filler hose
6.
EVAP hose
7.
Fuel valve assembly
8.
Fuel tank
9.
Fuel tank protector
10.
Fuel tank tightening band
PBIC0708E
FUEL TANK (YD22DDTI)
FL-15
C
D
E
F
G
H
I
J
K
L
M
A
FL
7.
Remove the quick connector. For disconnection procedure of the quick connector, refer to
●
Put mating marks on hoses for correct installation.
8.
Remove exhaust center tube and insulator.
9.
Remove fuel tank protector.
10. Using a transmission jack, support the bottom of the fuel tank.
11. Disconnect fuel filler hose, EVAP hose and vent hose at fuel
tank side.
For disconnection procedure of the quick connector, refer to
8, "FUEL LEVEL SENSOR UNIT (YD22DDTi)"
.
12. Remove fuel tank tightening band mounting bolts while support-
ing fuel tank.
13. Remove fuel tank.
INSTALLATION
●
Install in the reverse order of removal paying attention to the following.
●
The hose shall be inserted until it contacts with the stopper of the bracket end.
●
Be sure hose clamp is not positioned on swelled area of fuel tube.
●
Tighten fuel hose clamp so that the distance between its lugs becomes to the following.
●
Push the mounting band pin to the vehicle side securely.
●
Before fixing the fuel tank, temporarily install the fuel filler tube.
CAUTION:
Use genuine fuel filler tube mounting bolts or equivalent. Make sure to tighten them to the speci-
fied torque.
●
To connect the quick connector, refer to
FL-8, "FUEL LEVEL SENSOR UNIT (YD22DDTi)"
.
SFE644A
SFE641A
PBIC0712E
Fuel tank side
: 8 - 12 mm (0.31 - 0.47 in)
Fuel filler tube side
: 7 - 11 mm (0.28 - 0.43 in)
FL-16
FUEL TANK (YD22DDTI)
INSPECTION AFTER INSTALLATION
Run engine and check for fuel leaks at connections.
FUEL TANK (F9Q)
FL-17
C
D
E
F
G
H
I
J
K
L
M
A
FL
FUEL TANK (F9Q)
PFP:17202
Removal and Installation
EBS00SIT
REMOVAL
1.
Disconnect battery ground cable.
2.
Open fuel filler lid and filler cap.
3.
If necessary, drain fuel from fuel tank.
4.
Remove rear seat cushion. Refer to BT section in P12 ESM “SM2E00-1P12E0E”.
5.
Remove inspection hole cover under the rear seat.
MBIB0857E
1.
Fuel filler cap
2.
Grommet
3.
Fuel filler tube
4.
Vent hose
5.
Fuel filler hose
6.
EVAP hose
7.
Fuel check valve
8.
Fuel tank
9.
Fuel tank mounting band
10. Heat insulator
MBIB0521E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст