Nissan Primera P12. Instruction — part 185
LCD DISPLAY
DI-69
C
D
E
F
G
H
I
J
L
M
A
B
DI
SERVICE
●
In this mode, service schedule can be set on this display.
NOTE:
●
To set service schedule, change journey distance.
●
When the indicator of “Service Information Display” is set
green, the color of the journey distance marker will be red.
And automatically service information screen will be displayed
when journey distance is reached on service schedule.
MKIB0148E
DI-70
LCD DISPLAY
Power Supply and Ground Circuit Check for Display Unit
EKS009C3
1.
CHECK FUSE
Check that the following fuses in display are blown.
OK or NG
OK
>> GO TO 2.
NG
>> If fuse is blown, be sure to eliminate cause of problem before installing new fuse. Refer to
.
2.
POWER SUPPLY CIRCUIT CHECK
1.
Disconnect display connector.
2.
Check voltage between display unit harness connector and
ground.
OK or NG
OK
>> GO TO 3.
NG
>> Check harness for open or short between display and fuse.
3.
GROUND CIRCUIT CHECK
Check continuity between display unit and ground.
OK or NG
OK
>> Inspection end.
NG
>> Check ground harness.
Unit
Power souse
Fuse No.
Display
Battery power
33
Ignition switch ACC or ON
1
Terminals
Ignition switch position
(+)
(–)
OFF
ACC
ON
Connector
Terminal
(Wire color)
M61
2 (Y)
Ground
Battery
voltage
Battery
voltage
Battery
voltage
4 (Y)
Ground
Battery
voltage
Battery
voltage
Battery
voltage
6 (P)
Ground
0V
Battery
voltage
Battery
voltage
MKIB0101E
Terminals
Continuity
(+)
(–)
Connector
Terminal
(wire color)
M61
1 (B)
Ground
Yes
3 (B)
Ground
Yes
MKIB0102E
LCD DISPLAY
DI-71
C
D
E
F
G
H
I
J
L
M
A
B
DI
Power Supply and Ground Circuit Check for Multifunction Switch
EKS009C4
1.
CHECK FUSES
Check the fuse below.
OK or NG
OK
>> GO TO 2.
NG
>> If fuse is blown, be sure to eliminate cause of problem before installing new fuse. Refer to
.
2.
POWER SUPPLY CIRCUIT CHECK
1.
Disconnect multifunction switch connector.
2.
Check voltage between multifunction switch and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Check harness for open or short between multifunction switch and fuse.
3.
GROUND CIRCUIT CHECK
1.
Check continuity between multifunction switch harness connec-
tor M49 terminal 1 (B) and ground.
OK or NG
OK
>> Inspection end.
NG
>> Check ground harness.
Unit
Power source
Fuse No.
Multifunction switch
Ignition switch ACC or ON
1
Terminals
Ignition switch position
(+)
(–)
OFF
ACC
ON
Connector
Terminal
(Wire color)
M49
6 (P)
Ground
0V
Battery
voltage
Battery
voltage
MKIB0103E
Continuity should exist.
MKIB0104E
DI-72
LCD DISPLAY
Vehicle Speed Signal Check/LHD Models
EKS009C5
1.
HARNESS CHECK
1.
Disconnect display unit connector and combination meter connector.
2.
Check the following.
–
Continuity between display unit harness connector M61 terminal
11 (L/B) and combination meter harness connector M37 terminal
34 (L/B).
–
Continuity between display unit harness connector M61 terminal
11 (L/B) and ground.
OK or NG
OK
>> GO TO 2.
NG
>> Replace harness or connector.
2.
VEHICLE SPEED SIGNAL CHECK
Connect combination meter connector and display unit connector.
With CONSULT-II
1.
Lift up drive wheels.
2.
Start engine and drive vehicle at more than 20 km/h (12MPH).
3.
Check signal between display unit harness connector M61 ter-
minal 11(L/B) and ground when rotating wheels with engine at
idle. (Use “SIMPLE OSCILLOSCOPE” in “SUB MODE” with
CONSULT-II.)
Without CONSULT-II
1.
Lift up drive wheels.
2.
Start engine and drive vehicle at more than 20 km/h (12MPH).
3.
Check voltage between display unit harness connector M61 ter-
minal 11(L/B) and ground when rotating wheels with engine at
idle.
OK or NG
OK
>> Replace display unit.
NG
>> Check combination meter system. Refer to
bination Meter Self-Diagnosis"
.
Continuity should exist.
Continuity should not exist.
MKIB0207E
11– Ground:
MKIB0723E
ELF1080D
Voltage: Approximately 0 – 5V
MKIB0208E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст