Nissan Primera P12. Instruction — part 436
EM-90
[YD]
ENGINE ASSEMBLY
2.
Drain coolant from radiator drain plug.
3.
Remove the following parts.
●
LH/RH undercover
●
LH/RH front wheel
●
Battery
●
Engine cover
●
Auxiliary drive belt; Refer to
EM-14, "Removal and Installation"
.
●
Air duct and air cleaner case assembly; Refer to
EM-15, "Removal and Installation"
.
●
Alternator
●
Radiator and radiator fan assembly; Refer to
CO-10, "Removal and Installation"
.
4.
Disconnect engine room harness from the engine side and set it aside for easier work.
5.
Disconnect all the body-side vacuum hoses and air hoses at engine side.
Engine room LH
6.
Disconnect fuel feed and return hoses, and plug it to prevent fuel from draining.
7.
Disconnect heater hose, and install plug it to prevent engine coolant from draining.
8.
Remove clutch operating cylinder from transaxle, and move it aside.
9.
Disconnect shift cable from transaxle.
Engine room RH
10. Remove engine coolant reservoir tank.
11. Remove air conditioner compressor with piping connected from engine. Temporarily secure it on body
with a rope to avoid putting load on it.
Vehicle underbody
12. Remove exhaust front tube.
13. Remove steering shaft from steering gear.
14. Disconnect power steering fluid cooler piping at a point between body and engine.
15. Remove ABS sensor from brake caliper.
16. Remove brake caliper with piping connected from steering knuckle. Temporarily secure it on body with a
rope to avoid load on it.
17. Remove LH/RH suspension from steering knuckle under strut.
Removal
18. Install engine slingers into front right of cylinder head and rear
left of cylinder head.
19. Lift with hoist and secure the engine in position.
Slinger bolts:
: 30 - 37 N·m (3.0 - 3.8 kg-m, 22 - 27 ft-lb)
SBIA0191E
ENGINE ASSEMBLY
EM-91
[YD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
●
Use a instruction lift table caddy or equivalently rigid tool such as
a jack or trestle. Securely support bottom of engine and
transaxle, and simultaneously adjust hoist tension.
CAUTION:
Put a piece of wood or something similar as the support-
ing surface, secure a completely stable condition.
20. Remove RH engine mounting insulator.
21. Pull LH engine mounting through-bolt out.
22. Remove mounting bolts at front end of center member.
23. Remove front suspension member mounting bolts and nuts.
24. Remove engine, transaxle assembly with suspension member
from vehicle downward by carefully operating supporting tools.
CAUTION:
●
During the operation, make sure that no part interferes
with body side.
●
Before and during this lifting, always check if any har-
nesses are left connected.
●
During the removal operation, always be careful to pre-
vent vehicle from falling off the lift due to changes in the
center of gravity.
●
If necessary, support vehicle by setting a jack or equivalent tool at the rear.
25. Remove power steering pump with piping connected from engine. Move it aside on suspension member.
26. Remove front engine mounting and rear engine mounting through-bolts to remove suspension member.
27. Remove starter motor.
28. Separate engine and transaxle.
INSTALLATION
Install in the reverse order of removal.
●
Do not allow oil to get on mounting insulator. Be careful not to damage mounting insulator.
●
When installation directions are specified, install parts according to the direction marks on them referring
to components illustration.
●
Make sure that each mounting insulator is seated properly, and tighten mounting bolts and nuts.
INSPECTION AFTER INSTALLATION
●
Before starting engine check the levels of coolant, lubrications and working oils. If less than required
quantity, fill to the specified level.
●
Before starting engine, bleed air from fuel piping. Refer to
.
●
Run engine to check for unusual noise and vibration.
●
Warm up engine thoroughly to make sure there is no leakage of coolant, lubricants, working oil, fuel and
exhaust gas.
PBIC0734E
MBIA0087E
PBIC0748E
EM-92
[YD]
ENGINE ASSEMBLY
●
Bleed air from passages in pipes and tubes of applicable lines.
CYLINDER BLOCK
EM-93
[YD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
CYLINDER BLOCK
PFP:11010
Disassembly and Assembly
EBS00SO4
MBIA0015E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст