Nissan Primera P12. Instruction — part 426
EM-50
[YD]
FUEL PUMP
13. Install secondary timing chain.
●
When installing, match the alignment marks on sprockets with
color coded alignment marks (colored links) on the chain.
14. Install timing chain tension guide.
●
The upper bolt has a longer shank than the lower bolt.
15. Using a hexagon-head wrench [face to face 6 mm (0.24 in)
SST], install timing chain slack guide.
16. Install chain tensioner.
a.
Push the plunger of the chain tensioner. While holding it with a
push pin, install the chain tensioner.
b.
Using a hexagon-head wrench [face to face 5 mm (0.20 in)
SST], tighten bolts.
c.
Pull out the push pin. holding the plunger.
●
Check again that the alignment marks on the sprockets
and the colored alignment marks on the timing chain are
aligned.
MBIA0030E
SBIA0228E
SBIA0227E
FUEL PUMP
EM-51
[YD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
17. Install front chain case.
a.
Install tension guide on the back surface of front chain case.
●
Hold front chain case vertically when installing. Tension guide
may come off if front chain case is tilted.
b.
Apply Genuine Liquid Gasket or equivalent (Refer to
"Precautions for Liquid Gasket"
.) on both ends of arched area
(locations where rear chain case is adjoined) as shown in the
figure.
c.
Install front chain case.
●
When installing, align dowel pin on oil pump case with the pin
hole.
●
Install No. 6, 10 and 11 bolts with the rubber washer to the
front chain case.
d.
Tighten fixing bolts in the numerical order shown in the figure.
e.
After tightening all the bolts, re-tighten in the same order.
18. Install injection tube center.
19. Install the harness connector to fuel pump.
20. Install fuel hoses to fuel pump.
21. Hereafter, install in the reverse order of removal.
SBIA0189E
JEF370Y
JEM121G
EM-52
[YD]
ROCKER COVER
ROCKER COVER
PFP:13264
Removal and Installation
EBS00SNV
REMOVAL
1.
Remove engine cover. Refer to the figure at right.
2.
Remove harness connector from fuel injector.
3.
Remove injection tube. Refer to
.
PBIC0760E
1.
Nozzle oil seal
2.
Oil filler cap
3.
Gasket
4.
Rocker cover
MBIA0018E
ROCKER COVER
EM-53
[YD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
4.
Remove fuel injector oil seal.
●
Using a slotted screwdriver, pry flange to remove oil seal.
5.
Remove rocker cover.
●
Loosen holding bolts in the reverse order of that shown in the
figure and remove.
INSTALLATION
1.
Apply 3.0 mm (0.118 in) dia. of Genuine Liquid Gasket or equiv-
alent (Refer to
EM-6, "Precautions for Liquid Gasket"
.) on loca-
tions shown in the figure.
2.
Tighten holding bolts in the numerical order shown in the figure.
●
Re-tighten to the same torque in the same order as above.
3.
Install nozzle oil seal.
●
Insert it straight until flange fully contacts cylinder head.
4.
Install remaining parts in reverse order removal.
5.
Before starting engine, bleed air from fuel piping. Refer to
.
INSPECTION AFTER INSTALLATION
Start engine and increase engine speed to check for fuel leak.
PBIC0944E
SBIA0175E
JEM248G
SBIA0175E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст