Nissan Primera P12. Instruction — part 337
DTC P0563 BATTERY VOLTAGE
EC-533
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
3.
CHECK JUMPER CABLES INSTALLATION
Check that the jumper cables are connected in the correct sequence.
OK or NG
OK
>> GO TO 4.
NG
>> Reconnect jumper cables properly.
4.
CHECK BATTERY FOR BOOSTER
Check that the battery for the booster is a 12V battery.
OK or NG
OK
>> GO TO 5.
NG
>> Change the vehicle for booster.
5.
PERFORM DTC CONFIRMATION PROCEDURE AGAIN
Perform
EC-532, "DTC Confirmation Procedure"
, again.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
6.
REPLACE ECM
1.
Replace ECM.
2.
Perform initialization of NATS system and registration of all NATS ignition key IDs. Refer to
"NATS (Nissan Anti-theft System)"
.
3.
Perform Fuel Pump Learning Value Clearing. Refer to
EC-368, "Fuel Pump Learning Value Clearing"
.
>> INSPECTION END
7.
CHECK ELECTRICAL PARTS DAMAGE
Check the following for damage.
●
Wiring harness and harness connectors for burn
●
Fuses for short
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace malfunctioning part.
SEF439Z
EC-534
[YD (WITHOUT EURO-OBD)]
DTC P0580, P0581 ASCD STEERING SWITCH
DTC P0580, P0581 ASCD STEERING SWITCH
PFP:25551
Component Description
EBS0158J
ASCD steering switch has variant values of electrical resistance for
each button. ECM reads voltage variation of switch, and determines
which button is operated.
Refer to
EC-653, "AUTOMATIC SPEED CONTROL DEVICE
for the ASCD function.
CONSULT-II Reference Value in Data Monitor Mode
EBS0158K
Specification data are reference values.
ECM Terminals and Reference Value
EBS0158L
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
MBIB0234E
MONITOR ITEM
CONDITION
SPECIFICATION
SET SW
●
Ignition switch: ON
SET/COAST switch: Released
OFF
SET/COAST switch: Pressed
ON
RESUME/ACC SW
●
Ignition switch: ON
RESUME/ACCEL switch: Released
OFF
RESUME/ACCEL switch: Pressed
ON
CANCEL SW
●
Ignition switch: ON
CANCEL switch: Released
OFF
CANCEL switch: Pressed
ON
MAIN SW
●
Ignition switch: ON
ON/OFF switch: Released
OFF
ON/OFF switch: Pressed
ON
TERMI-
NAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA
(DC Voltage)
102
PU
ASCD steering switch
[Ignition switch ON]
●
ASCD steering switch is OFF.
Approximately 4.3V
[Ignition switch ON]
●
ON/OFF switch is ON.
Approximately 0.3V
[Ignition switch ON]
●
CANCEL switch is ON.
Approximately 1.3V
[Ignition switch ON]
●
SET/COAST switch is ON.
Approximately 2.3V
[Ignition switch ON]
●
RESUME/ACCEL switch is ON.
Approximately 3.3V
103
B
ASCD steering switch
ground
[Ignition switch ON]
Approximately 0.3V
DTC P0580, P0581 ASCD STEERING SWITCH
EC-535
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
On Board Diagnosis Logic
EBS0158M
The MI will not light up for this diagnosis.
NOTE:
If DTC P0580 or P0581 is displayed with DTC P0605, first perform the trouble diagnosis for DTC P0605.
Refer to
.
DTC Confirmation Procedure
EBS0158N
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Wait at least 10 seconds.
4.
Press ON/OFF switch for at least 10 seconds, then release it and wait at least 10 seconds.
5.
Press RESUME/ACCEL switch for at least 10 seconds, then release it and wait at least 10 seconds.
6.
Press SET COAST switch for at least 10 seconds, then release it and wait at least 10 seconds.
7.
Press CANCEL switch for at least 10 seconds, then release it and wait at least 10 seconds.
8.
If DTC is detected, go to
EC-537, "Diagnostic Procedure"
.
DTC No.
Trouble Diagnosis
Name
DTC Detecting Condition
Possible Cause
P0580
ASCD steering
switch circuit low
●
ECM detects that the ASCD steering switch is
stuck ON.
●
Harness or connectors
(The switch circuit is open or shorted.)
●
ASCD steering switch
●
ECM
P0581
ASCD steering
switch circuit high
●
An excessively high voltage signal from the ASCD
steering switch is sent to ECM.
EC-536
[YD (WITHOUT EURO-OBD)]
DTC P0580, P0581 ASCD STEERING SWITCH
Wiring Diagram
EBS0158O
MBWA0608E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст