Nissan Primera P12. Instruction — part 613
LU-14
[F9Q]
PRECAUTIONS
[F9Q]
PRECAUTIONS
PFP:00001
Precautions For Liquid Gasket
EBS00S2X
REMOVAL OF LIQUID GASKET
●
After removing the mounting bolts and nuts, separate the mating
surface using a seal cutter and remove the liquid gasket.
CAUTION:
Be careful not to damage the mating surfaces.
●
In areas where the cutter is difficult to use, use a plastic hammer
to lightly tap the gasket applied area.
CAUTION:
If for some unavoidable reason a tool such as a flat-bladed
screwdriver is used, be careful not to damage the mating
surfaces.
LIQUID GASKET APPLICATION PROCEDURE
1.
Using a scraper, remove the old liquid gasket adhering to the
gasket application surface and the mating surface.
●
Remove the liquid gasket completely from the groove of the
gasket application surface, mounting bolts and bolt holes.
2.
Wipe the gasket application surface and the mating surface with
white gasoline (lighting and heating use) to remove adhering
moisture, grease and foreign materials.
3.
Attach the liquid gasket to the tube presser.
Use Genuine Liquid Gasket or equivalent.
4.
Apply the gasket without breaks to the specified location with the
specified dimensions.
●
If there is a groove for the liquid gasket application, apply the
gasket to the groove.
●
As for the bolt holes, normally apply the gasket inside the
holes. If specified, it should be applied outside the holes.
Make sure to read the instruction in this instruction.
●
Within five minutes of gasket application, install the mating
component.
●
If the liquid gasket protrudes, wipe it off immediately.
●
Do not retighten after the installation.
●
After 30 minutes or more have passed from the installation, fill
the engine oil and coolant.
CAUTION:
If there are instructions in this instruction, observe them.
PBIC0275E
PBIC0003E
EMA0622D
SEM159F
PREPARATION
LU-15
[F9Q]
C
D
E
F
G
H
I
J
K
L
M
A
LU
PREPARATION
PFP:00002
Special Service Tools
EBS00S2Y
NISSAN tool number
(RENAULT tool number)
Tool name
Description
KV113C0020
(Mot.1281-01)
Oil filter wrench
Removing and installing oil filter
WS39930000
(
—
)
Tube presser
Pressing the tube of liquid gasket
MBIB0369E
S-NT052
LU-16
[F9Q]
ENGINE OIL
ENGINE OIL
PFP:KLA92
Inspection
EBS00S2Z
OIL LEVEL AND MUDDINESS
●
Before starting the engine, check the oil level placing vehicle
horizontally. If the engine is already started, stop it and allow 10
minutes before checking.
●
Make sure the oil level is within the range shown in the figure.
●
If it is out of range, adjust it.
●
Check the oil for white turbidity or remarkable contamination.
●
If the oil becomes turbid and white, it is highly probable that it is
contaminated with coolant. Find the cause and repair.
OIL LEAKAGE
Check for oil leakage around the following area.
●
Oil pan
●
Oil pan drain plug
●
Oil pressure switch
●
Vacuum pump
●
Oil pump housing
●
Mating surface between cylinder block and cylinder head
●
Mating surface between cylinder head and rocker cover
●
Oil cooler
●
Crankshaft oil seals
Changing Engine Oil
EBS00S30
WARNING:
●
Be careful not to burn yourself, as the engine oil is hot.
●
Prolonged and repeated contact with used engine oil may cause skin cancer: try to avoid direct
skin contact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as
soon as possible.
1.
Put vehicle horizontally.
2.
Warm up engine, and check for oil leakage from engine components.
3.
Stop engine and wait for 10 minutes.
4.
Remove oil pan drain plug and oil filler cap (with oil level gauge).
5.
Drain oil and refill with new engine oil.
Oil specification and viscosity:
●
Refer to
MA-15, "RECOMMENDED FLUIDS AND LUBRICANTS"
.
Oil capacity (Approximate):
●
The refill capacity depends on the oil temperature and drain time. Use these specifications for reference
only.
Always use the dipstick to the determine when the proper amount of oil is in the engine.
CAUTION:
●
Be sure to clean drain plug and install with new washer.
●
The refill capacity depends on the oil temperature and drain time. Use these specifications for ref-
erence only.
Always use the dipstick to the determine when the proper amount of oil is in the engine.
6.
Warm up engine and check area around drain plug and oil filter for oil leakage.
MBIB0936E
Drain and refill
With oil filter change
4.66
(4-1/8 Imp qt)
Without oil filter change
4.5
(4 Imp qt)
ENGINE OIL
LU-17
[F9Q]
C
D
E
F
G
H
I
J
K
L
M
A
LU
7.
Stop engine and wait for 10 minutes.
8.
Check oil level.
MBIB0936E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст