Nissan Primera P12. Instruction — part 196
WARNING CHIME
DI-113
C
D
E
F
G
H
I
J
L
M
A
B
DI
4.
CHECK KEY SWITCH
Check continuity between key switch connector M30 terminals 1 and
2.
OK or NG
OK
>> Key switch is OK.
NG
>> Replace key switch.
Front Door Switch (Driver side) Check
EKS009CZ
1.
CHECK FRONT DOOR SWITCH (DRIVER SIDE) INPUT SIGNAL
With CONSULT-II
●
Check front door switch (“DR DOOR SW”) in “DATA MONITOR”
mode with CONSULT-II.
Without CONSULT-II
●
Check voltage between smart entrance control unit harness
connector M42 terminal 43 (R/W) and ground.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 2.
Terminals
Condition
Continuity
(+)
(–)
Connector
Terminal
Terminal
M30
1
2
Inserted
Yes
Removed
No
MKIB0704E
When driver's door is open
: DR DOOR SW ON
When driver's door is closed
: DR DOOR SW OFF
MKIB0193E
Terminal
Condition
(Driver's door)
Voltage [V]
(+)
(–)
43 (R/W)
Ground
Open
Approx. 5
Closed
0
MKIB0018E
DI-114
WARNING CHIME
2.
CHECK DOOR SWITCH OPEN OR SHORT CIRCUIT
1.
Disconnect smart entrance control unit harness connector and front door switch (driver side) connector.
2.
Check the following.
–
Harness continuity between smart entrance control unit harness connector M42 terminal 43 (R/W) and
door switch (driver side) connector B16 terminal 1 (R/W).
–
Harness continuity between smart entrance control unit harness connector M42 terminal 43 (R/W) and
body ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
3.
CHECK DOOR SWITCH (DRIVER SIDE)
Check continuity between front door switch (driver side) connector
B16 terminal 1 (R/W) and body ground.
OK or NG
OK
>> Front door switch (driver side) is OK.
NG
>> Replace front door switch (driver side)
Terminals
Continuity
(+)
(–)
Connector
Terminal
(Wire color)
Connector
Terminal
(Wire color)
M42
43 (R/W)
B16 (R/W)
1 (W/R)
Yes
M42
43 (R/W)
Ground
No
MKIB0705E
Terminals
Condition
Continuity
(+)
(–)
Connector
Terminal
(Wire color)
B16
1 (R/W)
Ground
Door is open
Yes
Door is closed
No
MKIB0706E
WARNING CHIME
DI-115
C
D
E
F
G
H
I
J
L
M
A
B
DI
Seat Belt Buckle Switch Check (Driver side)
EKS009D0
1.
SMART ENTRANCE CONTROL UNIT SYSTEM INSPECTION
Perform the smart entrance control unit self-diagnosis. Refer to
BCS-11, "SELF-DIAG RESULTS MODE"
in
“Body control system (BCS)” section.
OK or NG
OK
>> GO TO 2.
NG
>> Check smart entrance control system.
2.
COMBINATION METER SELF-DIAGNOSIS INSPECTION
Perform combination meter self-diagnosis mode. Refer to
DI-14, "Combination Meter Self-Diagnosis"
(LHD
models) or
DI-37, "Combination Meter Self-Diagnosis"
(RHD models).
OK or NG
OK
>> GO TO 3.
NG
>> Check combination meter system.
3.
CHECK SEAT BELT BUCKLE SWITCH INPUT SIGNAL
1.
Turn ignition switch “ON”.
2.
Check voltage between seat belt buckle switch (driver side) har-
ness connector B12 terminal 1 (G/W) and ground.
OK or NG
OK
>> Seat belt buckle switch is OK.
NG
>> GO TO 4. (LHD models)
NG
>> GO TO 5. (RHD models)
4.
CHECK SEAT BELT BUCKLE SWITCH INPUT SIGNAL CIRCUIT (LHD MODELS)
1.
Turn ignition switch “OFF”.
2.
Disconnect combination meter harness connector and seat belt buckle switch (driver side) harness con-
nector.
3.
Check the following.
–
Harness continuity between combination meter harness connector M36 terminal 8 (G/W) and seat belt
buckle switch (driver side) harness connector B12 terminal 1 (G/W).
–
Harness continuity between combination meter harness connector M36 terminal 8 (G/W) and body
ground.
OK or NG
OK
>> GO TO 6.
NG
>> Repair or replace harness.
Terminal
Condition (Driver
side seat belt
buckle switch)
Voltage [V]
(+)
(–)
1 (G/W)
Ground
Fasten
Approx. 5
Unfasten
0
MKIB0707E
Terminal
Continuity
(+)
(–)
Connector
Terminal
(Wire color)
Connector
Terminal
(Wire color)
M36
8 (G/W)
B12
1 (G/W)
Yes
M36
8 (G/W)
Ground
No
MKIB0708E
DI-116
WARNING CHIME
5.
CHECK SEAT BELT BUCKLE SWITCH INPUT SIGNAL CIRCUIT (RHD MODELS)
1.
Turn ignition switch “OFF”.
2.
Disconnect combination meter harness connector and seat belt buckle switch (driver side) harness con-
nector.
3.
Check the following.
–
Harness continuity between combination meter harness connector M36 terminal 21 (G/W) and seat belt
buckle switch (driver side) harness connector B12 terminal 1 (G/W).
–
Harness continuity between combination meter harness connector M36 terminal 21 (G/W) and body
ground.
OK or NG
OK
>> GO TO 6.
NG
>> Repair or replace harness.
6.
CHECK SEAT BELT BUCKLE SWITCH GROUND CIRCUIT
Check harness continuity between seat belt buckle switch (driver
side) harness connector B12 terminal 2 (B) and body ground.
OK or NG
OK
>> GO TO 7.
NG
>> Repair or replace harness.
7.
CHECK SEAT BELT BUCKLE SWITCH
Check continuity between seat belt buckle switch (driver side) con-
nector B12 terminal 1 and 2.
OK or NG
OK
>> INSPECTION END.
NG
>> Replace seat belt buckle switch (driver side).
Terminal
Continuity
(+)
(–)
Connector
Terminal
(Wire color)
Connector
Terminal
(Wire color)
M36
21 (G/W)
B12
1 (G/W)
Yes
M36
21 (G/W)
Ground
No
MKIB0709E
Continuity should exist.
MKIB0710E
When seat belt
fastened
: Continuity should not exist.
When seat belt
unfastened
: Continuity should exist.
MKIB0022E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст