Nissan Primera P12. Instruction — part 604
LT-126
INTERIOR ROOM LAMP
Interior Room Lamp Timer Does Not Cancel
EKS009OE
1.
CHECK IGNITION ON SIGNAL
WITH CONSULT-II
Check ignition switch ON signal (“IGNITION SW”) in “DATA MONITOR” mode with CONSULT-II.
WITHOUT CONSULT-II
1.
Turn ignition switch ON.
2.
Check voltage between smart entrance control unit harness
connector M42 terminal 29 and ground.
OK or NG
OK
>> GO TO 2.
NG
>> Check the following.
●
10A fuse [No. 10, located in fuse block (J/B)]
●
Harness for open or short between smart entrance
control unit and fuse
Turn ignition switch ON
: ON
Turn ignition switch OFF
: OFF
MKIB0196E
29 (Y/G) - Ground
: Battery voltage
MKIB0581E
INTERIOR ROOM LAMP
LT-127
C
D
E
F
G
H
I
J
L
M
A
B
LT
2.
CHECK DOOR SWITCH INPUT SIGNAL
WITH CONSULT-II
Check driver door switch signal (“DR DOOR SW”) in “DATA MONITOR” mode with CONSULT-II.
WITHOUT CONSULT-II
1.
Turn ignition switch OFF.
2.
Check voltage between smart entrance control unit harness
connector and ground.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 3.
3.
CHECK DRIVER SIDE DOOR SWITCH
1.
Disconnect front door switch (driver side) connector.
2.
Check continuity between front door switch (driver side) terminal
1 and ground part of door switch.
OK or NG
OK
>> Check harness for open or short between smart
entrance control unit and front door switch (driver side).
NG
>> Replace front door switch (driver side).
DR DOOR SW
Driver side door is open
: ON
Driver side door is closed
: OFF
MKIB0197E
Connector
Terminal (wire color)
Driver side door
condition
Voltage (V)
(Approx.)
( + )
( - )
M42
43 (R/W)
Ground
Open : (ON)
0
Closed : (OFF)
Battery voltage
MKIB0073E
Terminal
Door switch
Continuity
1
Ground part of
door switch
Pushed
No
Released
Yes
PIIA3351E
LT-128
INTERIOR ROOM LAMP
4.
CHECK DOOR LOCK/UNLOCK SWITCH
WITH CONSULT-II
Check door lock/unlock switch signal (“CDL LOCK SW” or “CDL UNLOCK SW”) in “DATA MONITOR” mode
with CONSULT-II.
WITHOUT CONSULT-II
Check voltage between smart entrance control unit harness connec-
tor M41 terminals 13 or 14 and ground.
OK or NG
OK
>> Door lock/unlock switch is OK.
NG
>> GO TO 2.
5.
CHECK DOOR LOCK/UNLOCK SWITCH
1.
Disconnect door lock/unlock switch connector.
2.
Check continuity between door lock/unlock switch connector terminals 1, 2 and 3.
OK or NG
OK
>> Check the following.
●
Ground circuit for door lock/unlock switch
●
Harness for open short between door lock/unlock
switch and smart entrance control unit
NG
>> Replace door lock/unlock switch.
When door lock/unlock is
locked
: CDL LOCK SW ON
When door lock/unlock is
unlocked
: CDL UNLOCK SW ON
MKIB0198E
Connector
Terminals (wire color)
Condition
(Door lock/
unlock switch)
Voltage (V)
(Approx.)
(+)
(
−
)
M41
13 (GY)
Ground
Locked
0
Unlocked
Battery voltage
14 (BR/Y)
Locked
Battery voltage
Unlocked
0
MKIB0582E
Terminal
Door lock/unlock
switch condition
Continuity
1
3
Lock
Yes
2
Unlock
Yes
MKIB0261E
INTERIOR ROOM LAMP
LT-129
C
D
E
F
G
H
I
J
L
M
A
B
LT
Bulb Replacement
EKS009OF
INTERIOR ROOM LAMP
Refer to
.
STEP LAMP
1.
Remove the lens using a clip driver or a suitable tool.
2.
Remove the bulb.
ASHTRAY
Removal and installation, refer to
.
Removal and Installation
EKS009OG
INTERIOR ROOM LAMP
Refer to
.
STEP LAMP
1.
Using a clips driver or a suitable tool, press and remove the
metal clip of the step lamp.
2.
Disconnect the interior step lamp connector.
ASHTRAY
1.
Remove the A/T finisher. Refer to IP section in P12 ESM (SM2E00-1P12E0E).
2.
Remove the console box (front, rear).
3.
Remove the instrument finisher E.
4.
Remove the cluster lid C.
5.
Remove the audio assembly.
6.
Turn the bulb socket counterclockwise and unlock it.
MKIB0155E
MKIB0156E
MKIB0154E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст