Nissan Primera P12. Instruction — part 188
LCD DISPLAY
DI-81
C
D
E
F
G
H
I
J
L
M
A
B
DI
2.
COMMUNICATION SIGNAL (AV–ME) CHECK
1.
Connect display unit connector and combination meter connec-
tor.
2.
Turn ignition switch ON.
3.
Check voltage signal between display unit harness connector
M61 terminal 16 (R) and ground with oscilloscope or CONSULT-
II.
OK or NG
OK
>> GO TO 3.
NG
>> Replace display unit.
3.
COMMUNICATION SIGNAL (ME–AV) CHECK
1.
Turn ignition switch to ON and display.
2.
Check voltage signal between display unit harness connector
M61 terminal 18 (L) and ground with oscilloscope or CONSULT-
II.
OK or NG
OK
>> Replace display unit.
NG
>> Replace combination meter.
MKIB0697E
SKIA0169E
MKIB0698E
SKIA0170E
DI-82
LCD DISPLAY
No Fuel Information Is Displayed/No Warning Message Is Displayed/RHD Mod-
els
EKS009CI
1.
COMMUNICATION LINE (MA-AV, AV-ME) CIRCUIT CHECK
1.
Disconnect the display unit connector and combination meter
connector.
2.
Check continuity between display unit and ground.
3.
Check continuity between display unit and combination meter.
OK or NG
OK
>> GO TO 2.
NG
>> Replace harness or connector.
2.
COMMUNICATION SIGNAL (AV–ME) CHECK
1.
Connect display unit connector and combination meter connec-
tor.
2.
Turn ignition switch ON.
3.
Check voltage signal between display unit harness connector
M61 terminal 16 (R) and ground with oscilloscope or CONSULT-
II.
OK or NG
OK
>> GO TO 3.
NG
>> Replace display unit.
Terminals
Continuity
Connector
Terminal
(wire color)
Terminal
M61
16 (R)
Ground
No
18 (G)
Terminals
Continuity
Display unit
Combination meter
Connector
Terminal
(wire color)
Connector
Terminal
(wire color)
M61
16 (R)
M37
28 (R)
Yes
18 (G)
27 (G)
MKIB0699E
MKIB0697E
SKIA0169E
LCD DISPLAY
DI-83
C
D
E
F
G
H
I
J
L
M
A
B
DI
3.
COMMUNICATION SIGNAL (ME–AV) CHECK
1.
Turn ignition switch to ON and display.
2.
Check voltage signal between display unit harness connector
M61 terminal 18 (L) and ground with oscilloscope or CONSULT-
II.
OK or NG
OK
>> Replace display unit.
NG
>> Replace combination meter.
Multifunction Switch Does Not Operate
EKS009CJ
1.
POWER AND GROUND CIRCUIT CHECK
●
Check power and ground circuit. Refer to
DI-62, "Terminals and Reference Value for Multifunction Switch"
.
OK or NG
OK
>> Replace multifunction switch.
NG
>> Repair or replace harness.
Removal and Installation of Multifunction switch
EKS009CK
1.
Remove the cluster lid C. Refer to IP section in P12 ESM
(SM2E00-1P12E0E).
2.
Remove the screw (4), and remove the multifunction switch.
Removal and Installation of Display Unit
EKS009CL
1.
Remove the cluster lid C. Refer to IP section in P12 ESM
(SM2E00-1P12E0E).
2.
Remove the screws (2), and remove the display unit.
MKIB0698E
SKIA0170E
MKIB0143E
MKIB0047E
DI-84
WARNING LAMPS
WARNING LAMPS
PFP:24814
Schematic
EKS009CM
MKWA1025E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст