Nissan Primera P12. Instruction — part 90
POWER DOOR LOCK — SUPER LOCK —
BL-69
C
D
E
F
G
H
J
K
L
M
A
B
BL
BACK DOOR SWITCH
1.
CHECK BACK DOOR SWITCH INPUT SIGNAL
With CONSULT- II
Check door switch “TRUNK OPEN SWITCH” in “DATA MONITOR” mode with CONSULT- II.
Without CONSULT- II
Check voltage between smart entrance control unit harness connector and ground.
OK or NG
OK
>> Back door switch is OK.
NG
>> GO TO 2
2.
CHECK BACK DOOR SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect back door release actuator connector.
3.
Check continuity between back door release actuator terminals 1 and 2.
OK or NG
OK
>> Check the following.
●
Back door release actuator ground circuit
●
Harness for open or short between smart entrance
control unit and back door release actuator
NG
>> Replace back door release actuator.
TRUNK OPEN SW
Back door open
: ON
Back door close
: OFF
SIIA1635E
Connector
Terminal (wire color)
Back door
Voltage (V)
(Approx.)
(+)
(–)
M41
16 (G)
Ground
Closed
5
Open
0
SIIA1636E
Terminal
Back door condition
Continuity
1
2
Opened
Yes
Closed
No
MIIB0456E
BL-70
POWER DOOR LOCK — SUPER LOCK —
Key Switch Check
EIS005HJ
1.
CHECK KEY SWITCH INPUT SIGNAL
WITH CONSULT-II
Check key switch signal (“KEY IN DETECT”) in “DATA MONITOR”
mode with CONSULT-II.
WITHOUT CONSULT-II
Check voltage between smart entrance control unit harness connector M41 terminal 5 and ground.
OK or NG
OK
>> Key switch is OK.
NG
>> GO TO 2.
2.
CHECK KEY SWITCH
1.
Disconnect key switch connector.
2.
Check continuity between key switch terminal 1 and 2.
OK or NG
OK
>> Check the following.
●
10A fuse [No. 12, located in fuse block (J/B)]
●
Harness for open or short between key switch and
fuse
●
Harness for open or short between smart entrance control unit and key switch
NG
>> Replace key switch.
KEY IN DETECT
Key is inserted in ignition cylinder
: ON
Key is removed from ignition key cylinder
: OFF
MKIB0200E
Connector
Terminals (wire color)
Condition
(Door lock/
unlock switch)
Voltage (V)
(Approx.)
(+)
(
−
)
M41
5 (B/R)
Ground
Key is
inserted
Battery voltage
Key is
removed
0
MKIB0585E
Terminal
Condition
Continuity
1
2
Key is inserted
Yes
Key is removed
No
MKIB0586E
POWER DOOR LOCK — SUPER LOCK —
BL-71
C
D
E
F
G
H
J
K
L
M
A
B
BL
Super Lock Actuator Check
EIS005HK
FRONT DOOR
1.
CHECK OUTPUT SIGNAL FOR SUPER LOCK ACTUATOR
Check voltage between smart entrance control unit harness connector and ground.
OK or NG
OK
>> GO TO 2.
NG
>> Replace smart entrance control unit.
2.
CHECK SUPER LOCK ACTUATOR CIRUIT
1.
Turn ignition switch OFF.
2.
Disconnect smart entrance control unit and front door lock actuator assembly connector.
3.
Check continuity between smart entrance control unit harness
connector M43 terminal 52, 55 and front door lock actuator har-
ness connector D9 (driver side) or D38 (passenger side) termi-
nal 1, 2 (driver side) or 5, 6 (passenger side).
OK or NG
OK
>> Replace front door lock actuator (driver side) or (passenger side).
NG
>> Repair or replace harness between smart entrance control unit and front door lock actuator (driver
side) or (passenger side).
REAR DOOR
1.
CHECK OUTPUT SIGNAL FOR SUPER LOCK ACTUATOR
Check voltage between smart entrance control unit harness connector and ground.
OK or NG
OK
>> GO TO 2
NG
>> Replace smart entrance control unit.
Connector
Terminals (wire color)
Door lock/
unlock switch
condition
Voltage (V)
(Approx.)
(+)
(
−
)
M43
52 (Y)
Ground
Unlock
(Released)
0
→
Battery voltage
→
0
55 (W/B)
Lock (Set)
0
→
Battery voltage
→
0
MIIB0468E
Driver side
52 (Y) - 2 (Y)
: Continuity should exist.
55 (W/B) - 1 (W/B)
: Continuity should exist.
Passenger side
52 (Y) - 5 (Y)
: Continuity should exist.
55 (W/B) - 6 (W/B)
: Continuity should exist.
MIIB0469E
Connector
Terminals (wire color)
Door lock/
unlock switch
condition
Voltage (V)
(Approx.)
(+)
(
−
)
M43
50 (G)
Ground
Lock (Set)
0
→
Battery voltage
→
0
52 (Y)
Unlock
(Released)
0
→
Battery voltage
→
0
MIIB0470E
BL-72
POWER DOOR LOCK — SUPER LOCK —
2.
CHECK SUPER LOCK ACTUATOR
1.
Turn ignition switch OFF.
2.
Disconnect smart entrance control unit and rear door lock actuator assembly connector.
3.
Check continuity between smart entrance control unit harness
connector M43 terminal 50, 52 and rear door lock actuator har-
ness connector D56 (LH) terminal 2, 5 or D66 (RH) terminal 2, 5.
OK or NG
OK
>> Replace rear door lock actuator LH or RH.
NG
>> Repair or replace harness between smart entrance control unit and rear door lock actuator LH or
RH.
Trunk or Back Door Release Switch Check
EIS005HL
EXTERNAL SWITCH
1.
CHECK EXTERNAL TRUNK OR BACK DOOR RELEASE SWITCH INPUT SIGNAL
With CONSULT-II
Check external trunk or back door release switch input signal “EXT TRUNK REL” in “DATA MONITOR” mode
with CONSULT- II.
Without CONSULT- II
Check voltage between smart entrance control unit harness connector M41 terminal 20(BR) and ground.
OK or NG
OK
>> Trunk or back door release switch is OK.
NG
>> GO TO 2
Rear LH
50 (G) - 5 (G)
: Continuity should exist.
52 (Y) - 2 (Y)
: Continuity should exist.
Rear RH
50 (G) - 2 (G)
: Continuity should exist.
52 (Y) - 5 (Y)
: Continuity should exist.
MIIB0471E
Release switch is pushed (open):
EXT TRUNK REL ON
Release switch is released (close):
EXT TRUNK REL OFF
SIIA1603E
Connector
Terminal (wire color)
Release switch
Voltage (V)
(Approx.)
(+)
(–)
M41
20 (B/R)
Ground
Pushed
0
Released
5
SIIA1604E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст