Nissan Primera P12. Instruction — part 415
EM-6
[YD]
PRECAUTIONS
Precautions for Liquid Gasket
EBS00SNA
REMOVAL OF LIQUID GASKET SEALING
●
After removing the mounting bolts and nuts, separate the mating
surface using a seal cutter and remove the liquid gasket.
CAUTION:
Be careful not to damage the mating surfaces.
●
In areas where the cutter is difficult to use, use a plastic hammer
to lightly tap the areas where the liquid gasket is applied.
CAUTION:
If for some unavoidable reason a tool such as a flat-bladed
screwdriver is used, be careful not to damage the mating sur-
faces.
LIQUID GASKET APPLICATION PROCEDURE
1.
Using a scraper, remove the old liquid gasket adhering to the
gasket application surface and the mating surface.
●
Remove the liquid gasket completely from the groove of the gas-
ket application surface, mounting bolts, and bolt holes.
2.
Wipe the gasket application surface and the mating surface with
white gasoline (lighting and heating use) to remove adhering
moisture, grease and foreign materials.
3.
Attach the liquid gasket to the tube presser.
Use Genuine Liquid Gasket or equivalent.
4.
Apply the gasket without breaks to the specified location with the
specified dimensions.
●
If there is a groove for the liquid gasket application, apply the
gasket to the groove.
●
As for the bolt holes, normally apply the gasket inside the holes.
Occasionally, it should be applied outside the holes. Make sure
to read this service instruction.
●
Within five minutes of gasket application, install the mating com-
ponent.
●
If the liquid gasket protrudes, wipe it off immediately.
●
Do not retighten after the installation.
●
After 30 minutes or more have passed from the installation, fill
the engine oil and coolant.
CAUTION:
If there are specific instructions in this service instruction, observe
them.
PBIC0275E
PBIC0003E
EMA0622D
SEM159F
PREPARATION
EM-7
[YD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
PREPARATION
PFP:00002
Special Service Tools
EBS00SNB
Tool number
Tool name
Description
ST0501S000
Engine stand assembly
1 ST05011000
Engine stand
2 ST05012000
Base
Disassembling and assembling
KV10106500
Engine stand shaft
KV11105900
Engine sub-attachment
Used with KV10106500
KV10115600
Valve oil seal drift
Installing valve oil seal
Use side A.
Side A
a: 20 (0.79) dia.
b: 13 (0.51) dia.
c: 10.3 (0.406) dia.
d: 8 (0.31) dia.
e: 10.7 (0.421)
f: 5 (0.20)
Unit: mm (in)
KV10107902
Valve oil seal puller
1 KV10116100
Valve oil seal puller adapter
Removing valve oil seal
KV11103000
Injection pump drive gear puller
Removing crankshaft pulley
NT042
NT028
NT799
NT603
NT605
NT676
EM-8
[YD]
PREPARATION
KV101056S0
Ring gear stopper
1 KV10105630
Adapter
2 KV10105610
Plate
Preventing crankshaft from rotating
a: 3 (0.12)
b: 6.4 (0.252)
c: 2.8 (0.110)
d: 6.6 (0.260)
e: 107 (4.21)
f: 14 (0.55)
g: 20 (0.79)
h: 14 (0.55) dia.
Unit: mm (in)
KV101151S0
Lifter stopper set
1 KV10115110
Camshaft pliers
2 KV10115120
Lifter stopper
Changing valve lifter shims
ST16610001
Pilot bushing puller
Removing crankshaft pilot bushing
KV10111100
Seal cutter
Removing steel oil pan and rear timing chain
case
WS39930000
Tube presser
Pressing the tube of liquid gasket
KV10112100
Angle wrench
Tightening bolts for bearing cap, cylinder
head, etc.
KV10109300
Pulley holder
a: 68 mm (2.68 in)
b: 8 mm (0.31 in) dia.
Tool number
Tool name
Description
NT617
NT041
NT045
NT046
NT052
NT014
NT628
PREPARATION
EM-9
[YD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
KV11106010
Hexagon wrench
a: 5 mm (0.20 in) (Face to face)
b: 20 mm (0.79 in)
KV11106020
Hexagon wrench
a: 6 mm (0.24 in) (Face to face)
b: 20 mm (0.79 in)
KV11106030
Positioning stopper pin
a: 6 mm (0.24 in) dia.
b: 80 mm (3.15 in)
KV11106040
TORX wrench
a: T70
b: 26 mm (1.02 in)
KV11106050
Hexagonal wrench
a: 6 mm (0.24 in) (Face to face)
b: 42 mm (1.65 in)
Removing and installing mounting bolts of
fuel pump sprocket
KV11106060
Sprocket holder
Holding fuel pump sprocket
Tool number
Tool name
Description
NT801
NT803
NT804
NT805
SBIA0224E
SBIA0225E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст