Nissan Primera P12. Instruction — part 449
EM-142
[F9Q]
DRIVE BELTS
DRIVE BELTS
PFP:02117
Checking Drive Belts
EBS00SK2
WARNING:
Be sure to perform when the engine is stopped.
●
Inspect belts for cracks, fraying, wear and oil. If necessary,
replace.
Tension Adjustment
EBS00SK3
Belt tensioning is not necessary, as it is automatically adjusted by auto-tensioner.
CAUTION:
●
Keep oil and water away from belt.
●
Do not twist or bend belt excessively.
Removal and Installation
EBS00SK4
REMOVAL
1.
Remove engine undercover.
2.
Remove RH front wheel.
3.
Remove right side splash cover.
4.
Remove drive belt by turning the spanner to the right to loosen
the belt as shown.
INSTALLATION
Install in the reverse order of removal.
MBIB0944E
MBIB0714E
AIR CLEANER AND AIR DUCT
EM-143
[F9Q]
C
D
E
F
G
H
I
J
K
L
M
A
EM
AIR CLEANER AND AIR DUCT
PFP:16500
Removal and Installation
EBS00S5B
REMOVAL
1.
Disconnect battery ground cable.
2.
Remove engine room cover. Refer to
.
3.
Disconnect harness connector from the mass air flow sensor.
4.
Remove glow relay connector.
5.
Remove harness band and transaxle drain hose band.
6.
Remove air duct from air cleaner case side.
7.
Remove air cleaner case (upper).
8.
Remove air cleaner filter, then remove air cleaner case (lower).
9.
Remove air duct from turbocharger and PCV hose.
10. Remove mass air flow sensor from air cleaner case.
CAUTION:
Handle mass air flow sensor with care.
●
Do not shock it.
●
Do not disassemble it.
●
Do not touch its sensor.
INSTALLATION
●
Install in the reverse order of removal.
MBIB0945E
1.
Air duct dust side
2.
Resonator
3.
Air cleaner mounting
4.
Air cleaner case (lower)
5.
Air cleaner filter
6.
Air cleaner case (upper)
7.
Glow relay
8.
Mass air flow sensor
9.
Clamp
10. Air duct
EM-144
[F9Q]
AIR CLEANER AND AIR DUCT
Changing Air Cleaner Filter
EBS00S5C
REMOVAL
1.
Remove clips, and lift air cleaner case (upper).
2.
Remove air cleaner filter.
INSTALLATION
Install in the reverse order of removal.
MBIB0946E
CHARGE AIR COOLER
EM-145
[F9Q]
C
D
E
F
G
H
I
J
K
L
M
A
EM
CHARGE AIR COOLER
PFP:14461
Removal and Installation
EBS00S5D
REMOVAL
1.
Remove front bumper assembly. Refer to BT section in P12 ESM “SM2E00-1P12E0E”.
2.
Remove air inlet tubes.
3.
Remove charge air cooler.
CAUTION:
Do not damage charge air cooler core.
4.
Remove and install with bottom brackets as an assembly.
INSPECTION AFTER REMOVAL
Check air passages of charge air cooler core and fins for clogging, leaks or deformation. Clean or replace
charge air cooler if necessary.
●
Be careful not to deform core fins.
●
For cleaning procedure of charge air cooler core, refer to
.
INSTALLATION
Install in the reverse order of removal.
MBIB0947E
1.
Air inlet tube
2.
Air inlet hose
3.
Clamp
4.
Air inlet tube
5.
Air pressure sensor
6.
Shutter valve
7.
Air inlet hose
8.
Air inlet tube
9.
Air inlet hose
10. Charge air cooler
11. Rubber
12. Bracket
13. Bracket
14. Air inlet hose
15. Air inlet tube
16. Air inlet hose
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст