Nissan Versa Sedan. Instruction — part 672
SE-14
< REMOVAL AND INSTALLATION >
FRONT SEAT
REMOVAL AND INSTALLATION
FRONT SEAT
DRIVER SIDE
DRIVER SIDE : Exploded View
INFOID:0000000009268518
WITH REMOVABLE HEADREST
ALJIA0995ZZ
FRONT SEAT
SE-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
1.
Armrest (if equipped)
2.
Seat cushion outer finisher (RH)
3.
Seat belt buckle
4.
Seat cushion trim
5.
Seat cushion pad
6.
Seat cushion frame
7.
Seat cushion outer finisher (LH)
8.
Lift lever (if equipped)
9.
Lift lever cap (if equipped)
10. Recline lever
11. Side air bag module
12. Chute rod
13. Headrest holder (locked)
14. Seat frame assembly
15. Headrest holder (free)
16. Headrest
17. Seatback pad
18. Seatback trim
SE-16
< REMOVAL AND INSTALLATION >
FRONT SEAT
WITHOUT REMOVABLE HEADREST
ALJIA0996ZZ
1.
Seat frame assembly
2.
Seat cushion outer finisher (RH)
3.
Seat belt buckle
4.
Seat cushion trim
5.
Seat cushion pad
6.
Seat cushion frame
7.
Seat cushion outer finisher (LH)
8.
Lift lever (if equipped)
9.
Lift lever cap (if equipped)
10. Recline lever
11. Side air bag module
12. Chute rod
13. Seatback pad
14. Seatback trim
FRONT SEAT
SE-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
DRIVER SIDE : Removal and Installation
INFOID:0000000009268519
REMOVAL
WARNING:
Do not leave any objects (screwdrivers, tools, etc.) on the seat during seat repair. It can lead to per-
sonal injury if the side air bag module should accidentally deploy.
CAUTION:
• When removing or installing the seat trim, handle it carefully to keep dirt out and to avoid damage.
• When checking the power seat circuit for continuity using a circuit tester, do not confuse its connec-
tor with the side air bag module connector. Such an error may cause the air bag module to deploy.
• Do not drop, tilt, or bump the side air bag module while installing the seat. Always handle it with
care.
• After the front side air bag module inflates, the front seatback assembly must be replaced.
• When removing and installing the seat, use shop cloths to protect components from damage.
• Before removing the front seat, turn the ignition switch OFF, disconnect both battery cables and wait
at least three minutes.
1. Disconnect the negative and positive battery terminals and wait at least three minutes. Refer to
2. Slide the seat to the full forward position.
3. Remove the two rear seat bolts.
4. Slide the seat to the full rearward position.
5. Remove the two front seat bolts.
6. Tilt the seat rearward to disconnect the harness connectors from the seat and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Make sure that the seat harness or the floor trim is not damaged during installation.
NOTE:
• When installing the LH front seat, tighten the bolts in the order
shown.
PASSENGER SIDE
LH front seat bolt torque
: 40 Nm (4.1 kg-m, 30 ft-lb)
AWJIA0920ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст