Nissan Versa Sedan. Instruction — part 560
OIL COOLER
LU-15
< REMOVAL AND INSTALLATION >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
OIL COOLER
Exploded View
INFOID:0000000009269704
Removal and Installation
INFOID:0000000009269705
REMOVAL
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Remove the engine under cover. Refer to
.
2. Drain engine oil. Refer to
.
3. Drain engine coolant. Refer to
CO-8, "Draining Engine Coolant"
.
CAUTION:
Perform when engine is cold.
4. Remove oil filter. Refer to
LU-11, "Removal and Installation"
5. Remove water hoses from the oil cooler.
6. Remove oil cooler and O-ring.
CAUTION:
Do not reuse O-rings.
INSPECTION AFTER REMOVAL
1.
Radiator hose (upper)
2.
Hose clamp
3.
Radiator hose (lower)
4.
Hose clamp
5.
Water hose
6.
Oil cooler
7.
Connector bolt
8.
Water hose
9.
O-ring
A.
To radiator (upper side)
B.
To radiator (lower side)
10. Relief valve
AWBIA1138GB
LU-16
< REMOVAL AND INSTALLATION >
[HR16DE]
OIL COOLER
Oil Cooler
Check oil cooler for cracks. Check oil cooler for clogging by blowing compressed air through engine coolant
inlet. If necessary, replace oil cooler assembly.
Relief Valve
Inspect relief valve for movement, cracks and breaks by pushing the ball. If replacement is necessary, remove
the valve by prying it out using a suitable tool. Install a new valve by tapping it in place.
INSTALLATION
Installation is in the reverse order of removal.
• Ensure that no foreign objects are adhering to the sealing surfaces of the oil cooler and oil pan (upper).
• Tighten connector bolt after aligning cutout (1) on oil cooler with
protrusion (2) on oil pan (upper) side.
CAUTION:
• Do not reuse O-ring.
• Replace relief valve if removed.
INSPECTION AFTER INSTALLATION
• Before starting engine, check oil/fluid levels, including engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to
MA-12, "Fluids and Lubricants"
.
• Use procedure below to check for fuel leakage.
• Turn ignition switch ON (with engine stopped). With fuel pressure applied to fuel piping, check for fuel leak-
age at connection points.
• Start engine. With engine speed increased, check again for fuel leakage at connection points.
• Run engine to check for unusual noise and vibration.
NOTE:
If hydraulic pressure inside timing chain tensioner drops after removal and installation, slack in the guide
may generate a pounding noise during and just after engine start. However, this is normal. Noise will stop
after hydraulic pressure rises.
• Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gas, or any oils/fluids including
engine oil and engine coolant.
• Bleed air from passages in lines and hoses, such as in cooling system.
• After cooling down engine, again check oil/fluid levels, including engine oil and engine coolant. Refill to spec-
ified level, if necessary.
• Summary of the inspection items:
*Power steering fluid, brake fluid, etc.
AWBIA1139GB
Item
Before starting engine
Engine running
After engine stopped
Engine coolant
Level
Leakage
Level
Engine oil
Level
Leakage
Level
Transmission/
transaxle fluid
A/T and CVT Models
Leakage
Level/Leakage
Leakage
M/T Models
Level/Leakage
Leakage
Level/Leakage
Other oils and fluids*
Level
Leakage
Level
Fuel
Leakage
Leakage
Leakage
Exhaust gas
—
Leakage
—
SERVICE DATA AND SPECIFICATIONS (SDS)
LU-17
< SERVICE DATA AND SPECIFICATIONS (SDS)
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Periodical Maintenance Specification
INFOID:0000000009269706
ENGINE OIL CAPACITY (APPROXIMATE)
Unit: (US qt, lmp qt)
Engine Oil Pressure
INFOID:0000000009269707
Unit: kPa (kg/cm
2
, psi)
*: Engine oil temperature at 80
°C (176°F).
Drain and refill
With oil filter change
3.5 (3 3/4, 3 1/8)
Without oil filter change
3.2 (3 3/8, 2 7/8)
Dry engine (Overhaul)
3.5 (3 3/4, 3 1/8)
Engine Speed
Approximate discharge pressure*
M/T
A/T
CVT
600 rpm
More than 98 (1.0, 14.2)
2,000 rpm
More than 294 (3.0, 42.6)
6,000 rpm
More than 392 (4.0, 56.8)
MA-1
MAINTENANCE
C
D
E
F
G
H
I
J
K
L
M
B
MA
SECTION
MA
N
O
A
CONTENTS
MAINTENANCE
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
GENERAL MAINTENANCE . . . . . . . .
Explanation of General Maintenance . . . . . ....
PERIODIC MAINTENANCE . . . . . . . .
Periodic Maintenance . . . . . . . . . . . ....
RECOMMENDED FLUIDS AND LUBRI-
CANTS . . . . . . . . . . . . . . . .
Fluids and Lubricants . . . . . . . . . . . ..
SAE Viscosity Number . . . . . . . . . . .
Anti-Freeze Coolant Mixture Ratio . . . . . . ..
ENGINE MAINTENANCE . . . . . . . . ...
DRIVE BELT . . . . . . . . . . . . . . . ..
DRIVE BELT : Exploded View . . . . . . . .
DRIVE BELT : Inspection . . . . . . . . . .
DRIVE BELT : Adjustment . . . . . . . . . ..
ENGINE COOLANT . . . . . . . . . . . . ...
ENGINE COOLANT : Inspection . . . . . . . .
ENGINE COOLANT : Draining Engine Coolant . ..
ENGINE COOLANT : Refilling Engine Coolant . ...
ENGINE COOLANT : Flushing Cooling System . .
FUEL LINES . . . . . . . . . . . . . . . ..
FUEL LINES : Inspection . . . . . . . . . .
AIR CLEANER FILTER . . . . . . . . . . . .
AIR CLEANER FILTER : Exploded View . . . .
AIR CLEANER FILTER : Removal and Installation
ENGINE OIL . . . . . . . . . . . . . . . ...
ENGINE OIL : Inspection . . . . . . . . . . .
ENGINE OIL : Draining . . . . . . . . . . .
ENGINE OIL : Refilling . . . . . . . . . . .
OIL FILTER . . . . . . . . . . . . . . . .
OIL FILTER : Removal and Installation . . . . ...
OIL FILTER : Inspection . . . . . . . . . . ..
SPARK PLUG . . . . . . . . . . . . . . .
SPARK PLUG : Exploded View . . . . . . . ...
SPARK PLUG : Removal and Installation . . . ...
EVAP VAPOR LINES . . . . . . . . . . . .
EVAP VAPOR LINES : Inspection . . . . . . ...
CHASSIS AND BODY MAINTENANCE . . ...
EXHAUST SYSTEM . . . . . . . . . . . . ...
EXHAUST SYSTEM : Inspection . . . . . . .
CVT FLUID . . . . . . . . . . . . . . . . .
CVT FLUID : Inspection . . . . . . . . . . ...
CVT FLUID : Replacement . . . . . . . . . ..
CVT FLUID : Adjustment . . . . . . . . . . .
A/T FLUID . . . . . . . . . . . . . . . . ..
A/T FLUID : Inspection . . . . . . . . . . .
A/T FLUID : Changing . . . . . . . . . . . .
A/T FLUID : Adjustment . . . . . . . . . . ...
CLUTCH FLUID . . . . . . . . . . . . . . .
CLUTCH FLUID : Inspection . . . . . . . . ...
CLUTCH FLUID : Draining . . . . . . . . . ..
CLUTCH FLUID : Refilling . . . . . . . . . ...
M/T OIL . . . . . . . . . . . . . . . . . ..
M/T OIL : Inspection . . . . . . . . . . . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст