Nissan Versa Sedan. Instruction — part 193
DLK-90
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
DOOR SWITCH
3. Check continuity between door switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-69, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK DOOR SWITCH
DLK-90, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace malfunctioning door switch.
4.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
>> Inspection End.
Component Inspection
INFOID:0000000009268772
1.
CHECK DOOR SWITCH
1. Turn ignition switch OFF.
2. Disconnect malfunctioning door switch connector.
3. Check continuity between door switch terminals.
Is the inspection result normal?
Door switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
Front door switch
LH
B8
3
M100
47
Yes
Front door switch
RH
B16
45
Rear door switch
LH
B6
48
Rear door switch
RH
B17
46
Door switch
Ground
Continuity
Connector
Terminal
Front door switch LH
B8
3
No
Front door switch RH
B16
Rear door switch LH
B6
Rear door switch RH
B17
Door switch
Condition
Continuity
Terminal
Front door switch
LH
3
Ground part of door
switch
Door switch
Pressed
No
Released
Yes
Front door switch
RH
Pressed
No
Released
Yes
Rear door switch
LH
Pressed
No
Released
Yes
Rear door switch
RH
Pressed
No
Released
Yes
DOOR SWITCH
DLK-91
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
YES
>> Inspection End.
NO
>> Replace malfunction door switch.
DLK-92
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
HAZARD FUNCTION
HAZARD FUNCTION
Component Function Check
INFOID:0000000009268773
1.
CHECK FUNCTION
1. Select INTELLIGENT KEY of BCM using CONSULT.
2. Select FLASHER in ACTIVE TEST mode.
3. Touch LH or RH to check that it works normally.
Is the inspection result normal?
YES
>> Hazard warning lamp circuit is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009268774
1.
CHECK HAZARD SWITCH CIRCUIT
EXL-87, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
>> Inspection End.
INTELLIGENT KEY
DLK-93
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INTELLIGENT KEY
Component Function Check
INFOID:0000000009268775
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Check Intelligent Key relative signal strength.
• Confirm vehicle Intelligent Key antenna signal strength.
1.
CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “RKE OPE COUN1” in “DATA MONITOR” mode.
3. Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Intelligent Key is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009268776
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Check Intelligent Key relative signal strength.
• Confirm vehicle Intelligent Key antenna signal strength.
1.
CHECK INTELLIGENT KEY BATTERY
Check by connecting a resistance (approximately 300
Ω) so that the
current value becomes about 10 mA. Refer to
.
Is the measurement value within the specification?
YES
>> Replace Intelligent Key.
NO
>> Replace Intelligent Key battery.
Monitor item
Condition
RKE OPE COUN1
Check that the numerical value is changing while operating on the Intelligent Key.
Standard
: Approx. 2.5 - 3.0V
OCC0607D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст