Nissan Versa Sedan. Instruction — part 859
TM-342
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
P062F EEPROM
P062F EEPROM
Description
INFOID:0000000009268145
TCM compares the calculated value stored in the flash ROM with the value stored in TCM. If the calculated
value does not agree with the stored value, TCM judges this as a malfunction.
DTC Logic
INFOID:0000000009268146
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1. Start the engine.
2. Check the DTC.
Is “P062F” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009268147
1.
CHECK INTERMITTENT INCIDNT
GI-45, "Intermittent Incident"
Is the inspection result normal?
YES
TM-437, "Removal and Installation"
.
NO
>> Repair or replace malfunctioning parts.
DTC
Trouble diagnosis name
DTC detection condition
Possible causes
P062F
Internal Control Module EE-
PROM Error
Flash ROM error is detected when turning ON
the ignition switch.
• TCM (flash ROM)
• Harness or connector
[TCM power supply (back-up) circuit is
open or shorted]
P0705 TRANSMISSION RANGE SENSOR A
TM-343
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P0705 TRANSMISSION RANGE SENSOR A
DTC Logic
INFOID:0000000009268148
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Be careful of the driving speed.
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1. Start the engine.
2. Maintain the following conditions.
3. Shift the selector lever through entire positions from “P” to “L”. (Hold the selector lever at each position for
10 seconds or more.)
4. Check the first trip DTC.
Is “P0705” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009268149
1.
CHECK TCM INPUT SIGNALS
With CONSULT
1. Turn ignition switch ON.
2. Select “Data Monitor” in “TRANSMISSION”.
3. Select “D POSITION SW”, “N POSITION SW”, “R POSITION SW”, “P POSITION SW” and “L POSITION
SW”.
4. Shift the selector lever through entire positions from “P” to “L” and check ON/OFF of each monitor item.
DTC
Trouble diagnosis name
DTC detection condition
Possible causes
P0705
Transmission Range Sensor
A Circuit (PRNDL Input)
Two or more range signals simultaneously
stay ON continuously for 5 seconds under the
following diagnosis condition 1 and 2:
• Diagnosis condition 1 (continued for 5 sec-
onds or more)
- TCM power supply voltage: More than 11 V
• Diagnosis condition 2 (continued for 2 sec-
onds or more)
- Vehicle speed: Less than 3 km/h (2 MPH)
- Accelerator pedal position: 0.6/8 or less
- Idle switch: ON
- Stop lamp switch: ON
• Harness or connector
(Short circuit between transmission
range switch and TCM)
• Transmission range switch
Accelerator pedal position
: 0.0/8
Brake pedal
: Depressed
Vehicle speed
: 0 km/h (0 MPH)
Monitor item
Test condition
Condition
D POSITION SW
Selector lever: “D” position
On
Other than the above
Off
TM-344
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
P0705 TRANSMISSION RANGE SENSOR A
Without CONSULT
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Turn ignition switch ON.
4. Shift the selector lever from “P” to “L” and check voltage between TCM harness connector terminals and
ground.
Is the inspection result normal?
YES >> Check
intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO-1 [“D POSITION SW” is “ON” when selector is not in “D” position. (Or connector terminal 4 is at power
voltage.)]>>GO TO 2.
NO-2 [“N POSITION SW” is “ON” when selector is not in “N” position. (Or connector terminal 5 is at power
voltage.)]>>GO TO 4.
NO-3 [“R POSITION SW” is “ON” when selector is not in “R” position. (Or connector terminal 6 is at power
voltage.)]>>GO TO 6.
NO-4 [“P POSITION SW” is “ON” when selector is not in “P” position. (Or connector terminal 7 is at power
voltage.)]>>GO TO 8.
NO-5 [“L POSITION SW” is “ON” when selector is not in “L” position. (Or connector terminal 2 is at power
voltage.)]>>GO TO 10.
2.
CHECK D POSITION SW CIRCUIT (PART 1)
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Check continuity between TCM harness connector terminals.
N POSITION SW
Selector lever: “N” position
On
Other than the above
Off
R POSITION SW
Selector lever: “R” position
On
Other than the above
Off
P POSITION SW
Selector lever: “P” position
On
Other than the above
Off
L POSITION SW
Selector lever: “L” position
On
Other than the above
Off
TCM
Ground
Test condition
Voltage
Connector
Terminal
F44
2
Ground
Selector lever: “ L” position
Battery voltage
Other than the above
Approx. 0 V
4
Selector lever: “D” position
Battery voltage
Other than the above
Approx. 0 V
5
Selector lever: “N” position
Battery voltage
Other than the above
Approx. 0 V
6
Selector lever: “R” position
Battery voltage
Other than the above
Approx. 0 V
7
Selector lever: “P” position
Battery voltage
Other than the above
Approx. 0 V
Monitor item
Test condition
Condition
P0705 TRANSMISSION RANGE SENSOR A
TM-345
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
CHECK D POSITION SW CIRCUIT (PART 2)
1. Disconnect transmission position switch connector.
2. Turn ignition switch ON.
3. Check voltage between TCM harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 12.
NO
>> Repair or replace malfunctioning parts.
4.
CHECK N POSITION SW CIRCUIT (PART 1)
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Check continuity between TCM harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace malfunctioning parts.
5.
CHECK N POSITION SW CIRCUIT (PART 2)
1. Disconnect transmission position switch connector.
2. Turn ignition switch ON.
3. Check voltage between TCM harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 12.
NO
>> Repair or replace malfunctioning parts.
6.
CHECK P POSITION SW CIRCUIT (PART 1)
1. Turn ignition switch OFF.
TCM
Continuity
Connector
Terminal
F44
4
2
Not existed
5
6
7
TCM
Ground
Voltage
Connector
Terminal
F44
4
Ground
Approx. 0 V
TCM
Continuity
Connector
Terminal
F44
5
2
Not existed
4
6
7
TCM
Ground
Voltage
Connector
Terminal
F44
5
Ground
Approx. 0 V
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст