Nissan Versa Sedan. Instruction — part 206
DLK-142
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
HOOD
INSTALLATION
Installation is in the reverse order of removal.
• Tighten hood hinge bolts to specified torque. Refer to
DLK-140, "HOOD ASSEMBLY : Adjustment"
.
CAUTION:
• Before installing the hood hinge, apply anticorrosive agent onto the surface of the vehicle.
• After installation, perform hood assembly adjustment procedure. Refer to
• Check hood hinge rotating point for poor lubrication. If neces-
sary, apply a suitable multi-purpose grease.
HOOD SUPPORT ROD
HOOD SUPPORT ROD : Removal and Installation
INFOID:0000000009268836
REMOVAL
1. Support hood assembly using a suitable tool.
WARNING:
Bodily injury may occur if hood assembly is not supported properly when removing hood support
rod.
2. Rotate and remove hood support rod from grommet.
3. Release tab and remove grommet from hood hinge, if necessary.
INSTALLATION
Installation is in the reverse order of removal.
JMKIA7995ZZ
RADIATOR CORE SUPPORT
DLK-143
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
RADIATOR CORE SUPPORT
Exploded View
INFOID:0000000009268837
RADIATOR CORE SUPPORT UPPER
RADIATOR CORE SUPPORT UPPER : Removal and Installation
INFOID:0000000009268838
RADIATOR CORE SUPPORT UPPER
Removal
1. Remove ground harness bolt (A).
2. Remove horn. Refer to
HRN-6, "Removal and Installation"
3. Remove hood lock assembly and hood lock control cable assembly clip. Refer to
1.
Radiator upper seal
2.
Condenser side seal
3.
Radiator side seal (RH)
4.
Radiator side seal (LH)
5.
Radiator core support lower
6.
Radiator core support upper
JMKIA8149ZZ
JMKIA8026ZZ
DLK-144
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
RADIATOR CORE SUPPORT
4. Remove crash zone sensor. Refer to
SR-22, "Removal and Installation"
.
5. Remove radiator cap adapter bracket bolt (A) and radiator reser-
voir tank bolt (B).
6. Remove radiator upper seal clips.
7. Remove upper clips of radiator side seal (LH/RH).
8. Disconnect all harness clips.
9. Remove front bumper fascia upper side clips (A).
10. Remove radiator core support upper bolts.
11. Pull back on upper part of front bumper fascia (1) and then
remove radiator core support upper (2) by pulling upward.
Installation
Installation is in the reverse order of removal.
RADIATOR CORE SUPPORT LOWER
RADIATOR CORE SUPPORT LOWER : Removal and Installation
INFOID:0000000009268839
RADIATOR CORE SUPPORT LOWER
Removal
1. Remove under cover. Refer to
EXT-19, "Removal and Installation"
2. Remove radiator upper seal clips.
JMKIA8027ZZ
JMKIA8028ZZ
JMKIA8029ZZ
RADIATOR CORE SUPPORT
DLK-145
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3. Remove front bumper fascia upper side clips (A).
4. Remove fender protector (LH/RH) clips from radiator core support lower. Refer to
.
5. Remove lower clips of radiator side seal (LH/RH).
6. Remove lower clips of condenser side seal.
7. Use suitable tools (A) to suspend components and to prevent
them from falling.
CAUTION:
Use care to avoid damage to radiator and condenser.
8. Remove radiator core support lower bolts and radiator core support lower.
Installation
Installation is in the reverse order of removal.
JMKIA8028ZZ
JMKIA8030ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст