Nissan Versa Sedan. Instruction — part 473
REAR WINDOW GLASS
GW-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
Removal and Installation
INFOID:0000000009267753
REMOVAL
1. Remove rear parcel shelf finisher. Refer to
INT-25, "Removal and Installation"
2. Remove the harness connectors and grounds for the rear window glass defogger.
3. Remove rear window glass using piano wire or power cutting tool (A) and an inflatable pump bag (B).
• Mark the body and glass with a matching marks if the rear window glass is reused
• Apply protective tape around the rear window glass to protect the painted surface from damage.
WARNING:
Always wear safety glasses and heavy gloves to help prevent injuries.
CAUTION:
• Be careful not to scratch the glass when removing.
• Be careful not to set or stand the glass on its edge. Small chips may develop into cracks.
• Protect the painted surface around the rear window glass from damage.
IINSTALLATION
Installation is in reverse order of removal
• Use a Genuine Nissan Urethane Adhesive Kit (if available) or an equivalent and follow the instructions pro-
vided with it.
• The start and finish of the adhesive application shall be located at the middle of the glass bottom to assure
watertightness.
• Open a door window while the urethane adhesive is curing. This prevents the glass from being forced out by
passenger compartment air pressure when all door windows are closed.
• The molding must be installed securely so that it is in position and leaves no clearance.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive is completely
cured (approximately 24 hours). Curing time varies with temperature and humidity.
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
• Use in an open, well ventilated location. Avoid breathing the vapors. They may be harmful if
inhaled. Move immediately to an area with fresh air if affected by vapor inhalation.
• Driving the vehicle before the urethane adhesive is completely cured may affect the performance
of the rear window glass in an accident.
CAUTION:
• Do not use an adhesive that is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Pay attention to the expiration or manufacture date printed
on the box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
• Do not leave primers or adhesive cartridge unattended with their caps open or off.
• The vehicle should not be driven for 24 hours or more or until the urethane adhesive is completely
cured. Curing time varies depending on temperature and humidity. The curing time increases
under lower temperature and lower humidity.
10.
Roof panel assembly
11. Body side outer panel
12. Rear pillar finisher
13.
Rear parcel shelf finisher
D.
13.0 (0.51)
E.
14.0 (0.55)
F.
13.0 (0.51)
G.
14.0 (0.55)
H.
13.0 (0.51)
J.
14.0 (0.55)
K.
7.0 (0.28)
M.
12.0 (0.47)
N.
4.5 (0.18)
P.
5.0 (0.20)
PIIB5779E
GW-20
< REMOVAL AND INSTALLATION >
REAR WINDOW GLASS
Inspection
INFOID:0000000009267754
REPAIRING WATER LEAKAGE FOR REAR WINDOW GLASS
Leakage can be repaired without removing the glass.
Determine the extent of leakage if water is leaking between the urethane adhesive material and body or glass.
This can be done by applying water to the rear window glass area while pushing glass outward.
Apply primer (if necessary) and then urethane adhesive to the leakage point to stop the leakage.
FRONT DOOR GLASS
GW-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
FRONT DOOR GLASS
Exploded View
INFOID:0000000009267755
Removal and Installation
INFOID:0000000009267756
REMOVAL
1. Fully open front door glass.
2. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
3. Disconnect door mirror harness connector and remove the clip.
4. Remove front door sealing screen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape will remain on the sealing screen, if the sealing
screen is reused.
5. Partially remove front door glass run.
6. Perform the following to access glass bolts.
1.
Front door panel
2.
Front door lower sash (front)
3. Front door glass run
4.
Front door sealing screen
5.
Front door power window motor
6. Front door regulator
7.
Front door glass
8.
Front door lower sash (rear)
9. Regulator seal (instruction window)
10. Snap pin (instruction window)
11. Regulator handle (instruction window)
AWKIA1881ZZ
GW-22
< REMOVAL AND INSTALLATION >
FRONT DOOR GLASS
• Operate the main power window or power window and door
lock and unlock motor switch to raise or lower the door window
until the glass bolts (A) can be seen.
• Operate the regulator handle to raise or lower the door window
until the glass bolts (A) can be seen.
7. Remove the glass bolts.
8. Correctly position the front door glass to pull it out of the sash
and remove the door glass from the door.
9. Remove front door outside molding. Refer to
EXT-29, "Removal and Installation"
.
10. Remove front door glass run.
11. Remove front door lower sash (rear).
• Remove lower sash (rear) bolts.
• Hold the upper part of lower sash and then pull it up to remove.
12. Remove front door lower sash (front).
• Remove lower sash (front) bolt.
• Hold the upper part of lower sash and then pull it up to remove.
INSTALLATION
Installation is in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000009267757
FITTING INSPECTION
• Make sure that the glass fits securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. Loosen the regulator bolts, guide rail bolts, and glass and guide rail bolts to correct the glass
position if the clearance between the glass and sash is not parallel.
JMKIA8063ZZ
JMKIA8064ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст