Nissan Versa Sedan. Instruction — part 399
EX-4
< PERIODIC MAINTENANCE >
EXHAUST SYSTEM
PERIODIC MAINTENANCE
EXHAUST SYSTEM
Inspection
INFOID:0000000009267432
Check exhaust pipes, muffler, and mounting for improper attach-
ment, leaks, cracks, damage or deterioration. Repair or replace as
necessary.
SMA211A
EXHAUST SYSTEM
EX-5
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EX
N
P
O
REMOVAL AND INSTALLATION
EXHAUST SYSTEM
Exploded View
INFOID:0000000009267433
Removal and Installation
INFOID:0000000009267434
WARNING:
• Perform the operation with the exhaust system fully cooled. The system will be hot just after engine
stops.
• Be careful not to cut your hand on the heat insulator edge.
CAUTION:
Be sure to use genuine exhaust system parts or equivalents because they are designed for heat resis-
tance, corrosion resistance, proper fit, and shape
REMOVAL
Remove the exhaust system components using power tools.
• Disconnect each joint and mounting as necessary.
1.
Heated oxygen sensor 2
2.
Catalyst cover (upper)
3.
Seal bearing
4.
Catalyst cover (lower)
5.
Spring
6.
Spring
7.
Mounting rubber
8.
Main muffler
9.
Ring gasket
10. Center muffler
11. Mounting rubber
12. Seal bearing
13. Exhaust front tube
AWBIA1137GB
EX-6
< REMOVAL AND INSTALLATION >
EXHAUST SYSTEM
• Remove heated oxygen sensor 2 (1) as needed using Tool (A).
CAUTION:
Be careful not to damage heated oxygen sensor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Always replace seal bearings and ring gaskets with new ones when reassembling.
• Temporarily tighten nuts and bolts. Check each part for unusual interference and mounting rubber
interference, and then tighten them to the specified torque.
• Discard any heated oxygen sensor which has been dropped from a height of more than 0.5 m (19.7
in) onto a hard surface such as a concrete floor; replace with a new one.
• Before installing a new heated oxygen sensor 2, clean exhaust system threads using the heated oxy-
gen sensor thread cleaner and apply anti-seize lubricant.
• Do not over-tighten heated oxygen sensor 2. Doing so may cause damage to the heated oxygen sen-
sor 2, resulting in the MIL coming on.
• Prevent rust preventives from adhering to the sensor body.
• If heat insulator is badly deformed, repair or replace it. If deposits such as mud pile up on the heat
insulator, clean and inspect them.
• When installing heat insulator avoid large gaps or interference between heat insulator and each
exhaust pipe.
• Remove deposits from the sealing surface of each connection. Connect them securely to avoid
exhaust leaks.
• Avoid twisting or deforming the mounting rubbers when installing them.
Exhaust Manifold to Exhaust Front Tube
• When installing the seal bearing (2), insert it into the exhaust man-
ifold (1) in the direction shown.
• When installing the spring (3) and bolt (4), ensure the following:
- Make sure the spring (3) sits properly on the flange surface by
aligning it to the locator dimples (A).
- Make sure the bolt (4) does not contact the inside of the flange bolt
hole.
CAUTION:
Be careful not to damage seal bearing surface when install-
ing.
• Tighten bolt with spring.
CAUTION:
• Ensure springs are seated correctly on the flange and not sitting on (A).
• Assemble the seal bearing so that the bolt is located in the center of the flare flange hole without
contact with the flange.
Exhaust Front Tube to Center Muffler
Tool number
: KV10114400 (J-38365)
JPBIA3468ZZ
Oxygen sensor thread cleaner
: — (J-43897-18)
Oxygen sensor thread cleaner
: — (J-43897-12)
(5)
: Exhaust front tube
JPBIA3652ZZ
EXHAUST SYSTEM
EX-7
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EX
N
P
O
• When installing the seal bearing (2), insert it into the exhaust man-
ifold (1) in the direction shown.
• When installing the spring (3) and bolt (4), ensure the following:
- Make sure the spring (3) sits properly on the flange surface by
aligning it to the locator dimples (A).
- Make sure the bolt (4) does not contact the inside of the flange bolt
hole.
CAUTION:
Be careful not to damage seal bearing surface when install-
ing.
• Tighten bolt with spring.
CAUTION:
• Ensure springs are seated correctly on the flange and not sitting on (A).
• Assemble the seal bearing so that the bolt is located in the center of the flare flange hole without
contact with the flange.
INSPECTION AFTER INSTALLATION
• Ensure the clearance between the tail tube and rear bumper is evenly spaced.
• Check exhaust tube joints for exhaust leaks and unusual noises with the engine running.
• Ensure the mounting brackets and mounting rubbers are installed properly and free from undue stress.
• Improper installation could result in excessive noise and vibration.
(5)
: Exhaust front tube
JPBIA3652ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст