Nissan Versa Sedan. Instruction — part 601
MWI
THE LOW WASHER FLUID WARNING CONTINUES DISPLAYING, OR DOES
NOT DISPLAY
MWI-103
< SYMPTOM DIAGNOSIS >
[TYPE B]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE LOW WASHER FLUID WARNING CONTINUES DISPLAYING, OR
DOES NOT DISPLAY
Description
INFOID:0000000009266554
• The warning is still displayed even after washer fluid is added.
• The warning is not displayed even though the washer tank is empty.
Diagnosis Procedure
INFOID:0000000009266555
1.
CHECK WASHER FLUID LEVEL SWITCH
Perform a unit check for the washer fluid level switch. Refer to
MWI-99, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Replace washer fluid level switch.Refer to
2.
CHECK WASHER FLUID LEVEL SWITCH SIGNAL CIRCUIT
Check the washer fluid level switch signal circuit. Refer to
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-104, "Removal and Installation"
NO
>> Repair or replace harness or connector.
MWI-104
< REMOVAL AND INSTALLATION >
[TYPE B]
COMBINATION METER
REMOVAL AND INSTALLATION
COMBINATION METER
Removal and Installation
INFOID:0000000009266556
REMOVAL
1. Disconnect the negative battery terminal. Refer to
PG-63, "Removal and Installation"
2. Remove cluster lid A. Refer to
IP-19, "Removal and Installation"
3. Remove the combination meter screws.
4. Pull the combination meter straight out to disengage resin clips.
NOTE:
The illustration shows the clip positions on the back of the com-
bination meter.
5. Disconnect the harness connector from the combination meter and remove.
INSTALLATION
Installation is in the reverse order of removal.
JSNIA3895ZZ
MWI
COMBINATION METER
MWI-105
< UNIT DISASSEMBLY AND ASSEMBLY >
[TYPE B]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
UNIT DISASSEMBLY AND ASSEMBLY
COMBINATION METER
Exploded View
INFOID:0000000009266557
Disassembly and Assembly
INFOID:0000000009266558
DISASSEMBLY
1. Disengage the pawls of the finisher using a suitable tool and remove the finisher.
2. Remove the screws of the front cover.
3. Disengage the pawls of the front cover using a suitable tool.
4. Pull the front cover straight out to remove from the unified meter control unit.
CAUTION:
• Do not touch the display, pointer, the inside of front cover and the printed area of the dial during
the work.
• Keep away from magnetic sources.
• Do not damage the front cover.
ASSEMBLY
Assembly is in the reverse order of disassembly.
CAUTION:
• Do not touch the display, pointer, the inside of front cover and the printed area of the dial during the
work.
• Keep away from magnetic sources.
• Do not damage the front cover.
1.
Unified meter control unit
2.
Front cover
3.
Finisher
JSNIA3907ZZ
PB-1
BRAKES
C
D
E
G
H
I
J
K
L
M
SECTION
PB
A
B
PB
N
O
P
CONTENTS
PARKING BRAKE SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
PARKING BRAKE SYSTEM . . . . . . . ...
Inspection and Adjustment . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . .
PARKING BRAKE CONTROL . . . . . . ...
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . ..
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст