Nissan Versa Sedan. Instruction — part 236
DLK-262
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
KEYFOB ID SET UP WITHOUT CONSULT
KEYFOB ID SET UP WITHOUT CONSULT
ID Code Entry Procedure
INFOID:0000000009268969
KEYFOB ID SET UP WITHOUT CONSULT
NOTE:
• If a keyfob is lost, the ID code of the lost keyfob must be erased to prevent unauthorized use. A specific ID
code can be erased with CONSULT. However, when the ID code of a lost keyfob is not known, all controller
ALKIA2029GB
KEYFOB ID SET UP WITHOUT CONSULT
DLK-263
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
ID codes should be erased. After all ID codes are erased, the ID codes of all remaining and/or new keyfobs
must be re-registered.
To erase all ID codes in memory, register one ID code (keyfob) five times. After all ID codes are erased, the
ID codes of all remaining and/or new keyfobs must be re-registered.
• When registering an additional keyfob, the existing ID codes in memory may or may not be erased. If five ID
codes are stored in memory, when an additional code is registered, only the oldest code is erased. If less
than five ID codes are stored in memory, when an additional ID code is registered, the new ID code is added
and no ID codes are erased.
• If you need to activate more than two additional new keyfobs, repeat the procedure “Additional ID code
entry” for each new keyfob
DLK-261, "ID Code Entry Procedure"
(with CONSULT),
(without CONSULT).
• A maximum amount of five ID codes is allowed. When more than five ID codes are entered, the oldest ID
code will be erased.
• Even if same ID code that is already in the memory is input, the same ID code can be entered. The code is
counted as an additional code.
DLK-264
< SYMPTOM DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
POWER DOOR LOCK SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
POWER DOOR LOCK SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000009268970
DOOR LOCK/UNLOCK FUNCTION MALFUNCTION
NOTE:
• Before performing the diagnosis in the following table, check “WORK FLOW”. Refer to
• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
• If the following symptoms are detected, check systems shown in the “Diagnosis/service procedure” column
in this order.
Symptom
Diagnosis/service procedure
Reference page
Key reminder door function does not operate
properly.
1.
Check door switch.
2.
Check key switch.
3.
Check Intermittent Incident.
Power door lock does not operate with door
lock and unlock switch on main power window
and door lock/unlock switch or power window
and door lock/unlock switch RH.
1.
Check BCM Power supply and ground circuit.
2.
Check main power window and door lock and unlock switch.
3.
Check power window and door lock and unlock switch RH.
4.
Check Intermittent Incident.
Specific door lock actuator does not operate.
1.
Check door lock actuator.
Driver side
Passenger side
Rear LH
Rear RH
2.
Check Intermittent Incident.
Power door locks do not operate with front
door lock key cylinder switch LH.
1.
Check key cylinder switch.
2.
Replace BCM.
Vehicle speed sensing auto door LOCK oper-
ation does not operate.
1.
Ensure automatic door lock/unlock function (lock operation)
is enabled.
2.
Check combination meter vehicle speed signal.
(Type
B)
(Type
A)
3.
Check intermittent incident.
Ignition OFF interlock auto door UNLOCK
function does not operate.
1.
Ensure automatic door lock/unlock function (unlock opera-
tion) is enabled.
2.
Check BCM for DTCs.
3.
Check intermittent incident.
REMOTE KEYLESS ENTRY SYSTEM SYMPTOMS
DLK-265
< SYMPTOM DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOTE KEYLESS ENTRY SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000009268971
REMOTE KEYLESS ENTRY SYSTEM
Symptom
Diagnoses/service procedure
Reference
page
All functions of remote keyless entry system do not
operate.
1. Keyfob battery and function check (use Remote Keyless Entry
Tester J-43241 or Signal Tech II Tool J-50190)
NOTE:
If the result of keyfob function check is OK, keyfob is not malfunc-
tioning.
2. Check BCM and remote keyless entry receiver.
The new ID of keyfob cannot be entered.
1. Keyfob battery and function check (use Remote Keyless Entry
Tester J-43241 or Signal Tech II Tool J-50190)
NOTE:
If the result of keyfob function check is OK, keyfob is not malfunc-
tioning.
2. Door switch check
3. ACC power check
4. Replace BCM.
Door lock or unlock does not function.
(If the power door lock system does not operate
instructionly, check power door lock system)
1. Keyfob battery and function check (use Remote Keyless Entry
Tester J-43241 or Signal Tech II Tool J-50190)
NOTE:
If the result of keyfob function check is OK, keyfob is not malfunc-
tioning.
2. Replace BCM.
Hazard and horn reminder does not activate properly
when pressing lock or unlock button of keyfob.
1. Check hazard and horn reminder mode with CONSULT
NOTE:
Hazard and horn reminder mode can be changed.
First check the hazard and horn reminder mode setting.
2. Door switch check
3. Replace BCM.
Hazard reminder does not activate properly when
pressing lock or unlock button of keyfob.
(Horn reminder OK)
1. Check hazard reminder mode with CONSULT
NOTE:
Hazard reminder mode can be changed.
First check the hazard reminder mode setting.
2. Check hazard function with hazard switch
—
3. Replace BCM.
Horn reminder does not activate properly when
pressing lock or unlock button of keyfob.
(Hazard reminder OK)
1. Check horn reminder mode with CONSULT
NOTE:
Horn reminder mode can be changed.
First check the horn reminder mode setting.
2. Check horn function with horn switch
—
3. IPDM E/R operation check
4. Replace BCM.
Room lamp illumination does not operate properly.
1. Room lamp operation check
2. Door switch check
3. Replace BCM.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст