Nissan Versa Sedan. Instruction — part 152
CLUTCH FLUID
CL-9
< PERIODIC MAINTENANCE >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
5. Slide clutch tube (1) for the specified distance (A) in the direction
of the arrow (
) as shown and immediately depress the clutch
pedal and hold it, to bleed the air from the system.
CAUTION:
Clutch tube is under hydraulic pressure; do not allow the
clutch tube to disconnect from the bleeding connector.
6. Return clutch tube and lock pin in their original positions.
7. Release clutch pedal and wait for 5 seconds.
8. Repeat steps 3 to 7 until no bubbles are observed in the clutch fluid.
9. Check that the fluid level in the reservoir tank is within the specified range after air bleeding. Refer to
.
(2)
: Bleeding connector
Dimension (A)
: 5 mm (0.20 in)
JPDIB0147ZZ
CL-10
< REMOVAL AND INSTALLATION >
CLUTCH PEDAL
REMOVAL AND INSTALLATION
CLUTCH PEDAL
Exploded View
INFOID:0000000009267495
Removal and Installation
INFOID:0000000009267496
REMOVAL
1. Remove the instrument lower panel LH. Refer to
IP-20, "Removal and Installation"
.
2. Disconnect master cylinder rod end from clutch pedal.
3. Disconnect clutch interlock switch connector.
4. Remove harness clip from clutch pedal.
5. Remove clutch pedal nuts and remove clutch pedal from the
vehicle.
6. Remove pedal pad from clutch pedal.
7. Remove clutch interlock switch and clip from clutch pedal.
8. Remove pedal stopper rubber from clutch pedal, using a suit-
able tool.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Press master cylinder rod end into clutch pedal until it stops.
Inspection and Adjustment
INFOID:0000000009267497
INSPECTION AFTER REMOVAL
• Check clutch pedal for bend, damage, or a cracked weld. If bend, damage, or a cracked weld is found,
replace clutch pedal.
• Check pedal stopper rubber. If damage or deformation is found, replace pedal stopper rubber.
• Check pedal pad. If wear or damage is found, replace pedal pad.
INSPECTION AND ADJUSTMENT AFTER INSTALLATION
1.
Clutch pedal
2.
Pedal stopper rubber
3.
Pedal pad
4.
Clip
5.
Clutch interlock switch
AWDIA0944GB
PCIB1491E
CLUTCH PEDAL
CL-11
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
Inspect the clutch interlock switch position and adjust as necessary. Refer to
CL-12
< REMOVAL AND INSTALLATION >
CLUTCH MASTER CYLINDER
CLUTCH MASTER CYLINDER
Exploded View
INFOID:0000000009267498
Removal and Installation
INFOID:0000000009267499
CAUTION:
• Do not spill clutch fluid onto painted surfaces. If fluid spills, wipe up immediately and wash the
affected area with water.
• Do not disassemble clutch master cylinder.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove battery. Refer to
PG-63, "Removal and Installation"
2. Remove IPDM E/R bracket bolts (A) and nut (B).
3. Remove IPDM E/R bracket (1).
4. Remove ECM bracket nuts (A).
1.
Reservoir hose
2.
Master cylinder
JPDIB0222ZZ
: Front
JPDIC0818ZZ
: Front
JPDIB0233ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст