Nissan Versa Sedan. Instruction — part 239
DLK-274
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
HOOD
REMOVAL AND INSTALLATION
HOOD
Exploded View
INFOID:0000000009268975
HOOD ASSEMBLY
HOOD ASSEMBLY : Removal and Installation
INFOID:0000000009268976
CAUTION:
• Use two people when removing or installing hood assembly due to its heavy weight.
• Use protective tape or shop cloths to protect surrounding components from damage during removal
and installation of hood assembly.
REMOVAL
1. Support hood assembly using a suitable tool.
WARNING:
Bodily injury may occur if hood assembly is not supported properly when removing hood assem-
bly.
2. Remove hood hinge to hood nuts and then remove the hood assembly.
CAUTION:
Use two people when removing or installing hood assembly due to its heavy weight.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, perform the hood assembly adjustment procedure. Refer to
.
1.
Hood assembly
2.
Hood bumper rubber
3.
Hood hinge (LH)
4.
Grommet
5.
Hood hinge (RH)
6.
Hood support rod
7.
Clamp
AWKIA1877ZZ
HOOD
DLK-275
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• After adjusting, apply touch-up paint (tbody color) onto the head of hood hinge bolts and nuts.
HOOD ASSEMBLY : Adjustment
INFOID:0000000009268977
Check the clearance and the surface height between hood and each part by visual inspection and tactile feel.
If the clearance and the surface height are out of specification, adjust them according to the adjustment proce-
dure.
Unit: mm (in)
1.
Hood assembly
2.
Hood bumper rubber
3.
Hood hinge (LH)
4.
Hood lock assembly
5.
Front bumper fascia
6.
Front combination lamp (LH)
7.
Front fender
AWKIA1878GB
Section
Item
Measurement
Standard
Difference (RH/LH,
MAX)
A – A
D
Clearance
4.4
± 2.5 (0.17 ± 0.10)
—
E
Surface height
-0.5
± 2.0 (0.02 ± 0.08)
< 3.0 (0.12)
B – B
F
Clearance
4.0
± 2.1 (0.16 ± 0.08)
< 2.5 (0.10)
G
Surface height
0.7
± 2.0 (0.03 ± 0.08)
< 2.0 (0.08)
C – C
H
Clearance
3.5
± 1.0 (0.14 ± 0.04)
< 1.5 (0.06)
I
Surface height
0.0
± 1.0 (0.0 ± 0.04)
< 1.5 (0.06)
DLK-276
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
HOOD
ADJUSTMENT PROCEDURE
1. Remove hood lock assembly, and then adjust the surface height of hood assembly, front fender assembly,
and front combination lamp according to the specifications provided torque of 22 N·m (2.2 kg-m, 16 ft-lb).
2. Position hood lock assembly (1) and engage primary striker (2).
Check hood lock assembly and primary striker for looseness.
3. Move hood lock assembly laterally until the center of primary striker and hood lock assembly are vertical
when viewed from the front.
4. After adjustment, tighten hood lock assembly bolts to the specified torque.
5. Rotate bumper rubber a minimum of 1/8 of a rotation counterclockwise in an upward direction.
CAUTION:
If any looseness is felt in hood striker or hood lock assembly, rotate bumper rubber more than 1/8
of a rotation.
6. Check that secondary latch (1) is securely engaged with sec-
ondary striker (2) from the dead load of the hood assembly.
7. Check that primary latch (1) is securely engaged with primary
striker (2) when hood is dropped with hood’s own weight from
approximately 200 mm (7.9 in) height.
8. Close hood assembly with a static closing force of 300 – 490 N (30.6 – 50.0 kg-f, 67.4 – 110 lb-f).
HOOD HINGE
HOOD HINGE : Removal and Installation
INFOID:0000000009268978
REMOVAL
1. Remove hood assembly. Refer to
DLK-274, "HOOD ASSEMBLY : Removal and Installation"
2. Remove hood support rod and grommet. Refer to
DLK-277, "HOOD SUPPORT ROD : Removal and
.
3. Remove front fender. Refer to
DLK-281, "FRONT FENDER : Removal and Installation"
4. Remove hood hinge bolts and remove hood hinge.
JMKIA7992ZZ
JMKIA7993ZZ
JMKIA7994ZZ
HOOD
DLK-277
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check hood hinge rotating point for poor lubrication. If necessary, apply a suitable multi-purpose
grease.
• Perform hood fitting adjustment procedure. Refer to
DLK-275, "HOOD ASSEMBLY : Adjustment"
.
• After adjusting, apply touch-up paint (body color) onto the
head of hood hinge bolts and nuts.
HOOD SUPPORT ROD
HOOD SUPPORT ROD : Removal and Installation
INFOID:0000000009268979
REMOVAL
1. Support hood assembly using a suitable tool.
WARNING:
Bodily injury may occur if hood assembly is not supported properly when removing hood support
rod.
2. Rotate and remove hood support rod from grommet.
3. Release tab and remove grommet from hood hinge, if necessary.
INSTALLATION
Installation is in the reverse order of removal.
JMKIA7995ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст