Nissan Versa Sedan. Instruction — part 814
TM-162
< DTC/CIRCUIT DIAGNOSIS >
[4AT: RE4F03C]
P072C STUCK IN 1GR
P072C STUCK IN 1GR
DTC Logic
INFOID:0000000009267919
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
• “
” must be performed before starting “DTC CONFIRMATION PROCE-
DURE”.
• Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause
secondary malfunction.
• Always drive vehicle at a safe speed.
1.
PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1. Start the engine.
2. Select the D position.
3. Drive the vehicle.
4. Maintain the following conditions for 5 seconds or more.
5. Check the first trip DTC.
Is “P072C” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009267920
1.
MALFUNCTION CAUSE SIMULATION TEST
GI-45, "Intermittent Incident"
Is the check result normal?
YES
>> Replace the transaxle assembly. Refer to
TM-250, "Removal and Installation"
.
NO
>> Repair or replace the malfunctioning parts.
DTC
Trouble diagnosis name
DTC detection condition
Possible causes
P072C
Stuck in Gear 1
The following diagnosis condi-
tions are met and the detection
conditions continue for 0.5 sec-
onds or more.
• Diagnosis condition
- Shifting is not in progress.
- Stop lamp switch OFF
• Detection conditions
- Deceleration: Less than
−
0.35 G
- Gear ratio: 6% or more, or
−
6% or less compared with
normal gear ratio
• 2-4 brake solenoid valve
• Control valve assembly
Selector lever
: 1 position
Stop lamp switch
: OFF
Vehicle speed
: 20 km/h (13 MPH) or more
P072D STUCK IN 2GR
TM-163
< DTC/CIRCUIT DIAGNOSIS >
[4AT: RE4F03C]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P072D STUCK IN 2GR
DTC Logic
INFOID:0000000009267921
DTC DETECTION LOGIC
DTC REPRODUCTION PROCEDURE
CAUTION:
• “
” must be performed before starting “DTC CONFIRMATION PROCE-
DURE”.
• Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause
secondary malfunction.
• Always drive vehicle at a safe speed.
1.
PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1. Start the engine.
2. Drive the vehicle.
3. Maintain the following conditions for 5 seconds or more.
4. Check the first trip DTC.
Is “P072D” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009267922
1.
MALFUNCTION CAUSE SIMULATION TEST
GI-45, "Intermittent Incident"
.
Is the check result normal?
YES
>> Replace the transaxle assembly. Refer to
TM-250, "Removal and Installation"
.
NO
>> Repair or replace the malfunctioning parts.
DTC
Trouble diagnosis name
DTC detection condition
Possible causes
P072D
Stuck in Gear 2
The following diagnosis condi-
tions are met and the detection
conditions continue for 0.5 sec-
onds or more.
• Diagnosis condition
- Shifting is not in progress.
- Stop lamp switch OFF
• Detection conditions
- Deceleration: Less than –
0.35 G
- Gear ratio: 6% or more, or
−
6% or less compared with
normal gear ratio
• High clutch/low & reverse
brake solenoid valve
• Control valve assembly
Selector lever
: 2 position
Gear
: 2GR
Stop lamp switch
: OFF
Vehicle speed
: 20 km/h (13 MPH) or more
TM-164
< DTC/CIRCUIT DIAGNOSIS >
[4AT: RE4F03C]
P072E STUCK IN 3GR
P072E STUCK IN 3GR
DTC Logic
INFOID:0000000009267923
DTC DETECTION LOGIC
DTC REPRODUCTION PROCEDURE
CAUTION:
• “
” must be performed before starting “DTC CONFIRMATION PROCE-
DURE”.
• Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause
secondary malfunction.
• Always drive vehicle at a safe speed.
1.
PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1. Start the engine.
2. Drive the vehicle.
3. Maintain the following conditions for 5 seconds or more.
4. Check the first trip DTC.
Is “P072E” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009267924
1.
MALFUNCTION CAUSE SIMULATION TEST
GI-45, "Intermittent Incident"
Is the check result normal?
YES
>> Replace the transaxle assembly. Refer to
TM-250, "Removal and Installation"
.
NO
>> Repair or replace the malfunctioning parts.
DTC
Trouble diagnosis name
DTC Detection Condition
Possible causes
P072E
Stuck in Gear 3
The following diagnosis condi-
tions are met and the detection
conditions continue for 0.5 sec-
onds or more.
• Diagnosis condition
- Shifting is not in progress.
- Stop lamp switch OFF
• Detection conditions
- Deceleration: Less than –
0.35 G
- Gear ratio: 6% or more, or
−
6% or less compared with
normal gear ratio
• 2-4 brake solenoid valve
• Control valve assembly
Selector lever
: D position (O/D OFF)
Gear
: 3GR
Stop lamp switch
: OFF
Vehicle speed
: 20 km/h (13 MPH) or more
P072F STUCK IN 4GR
TM-165
< DTC/CIRCUIT DIAGNOSIS >
[4AT: RE4F03C]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P072F STUCK IN 4GR
DTC Logic
INFOID:0000000009267925
DTC DETECTION LOGIC
DTC REPRODUCTION PROCEDURE
CAUTION:
• “
” must be performed before starting “DTC CONFIRMATION PROCE-
DURE”.
• Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause
secondary malfunction.
• Always drive vehicle at a safe speed.
1.
PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn the ignition switch OFF and wait for
at least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1. Start the engine.
2. Drive the vehicle.
3. Maintain the following conditions for 5 seconds or more.
4. Check the first trip DTC.
Is “P072F” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009267926
1.
MALFUNCTION CAUSE SIMULATION TEST
GI-45, "Intermittent Incident"
.
Is the check result normal?
YES
>> Replace the transaxle assembly. Refer to
TM-250, "Removal and Installation"
.
NO
>> Repair or replace the malfunctioning parts.
DTC
Trouble diagnosis name
DTC detection condition
Possible causes
P072F
Stuck in Gear 4
The following diagnosis condi-
tions are met and the detection
conditions continue for 0.5 sec-
onds or more.
• Diagnosis condition
- Shifting is not in progress.
- Stop lamp switch OFF
• Detection conditions
- Deceleration: Less than
−
0.35 G
- Gear ratio: 6% or more, or
−
6% or less compared with
normal gear ratio
• Low clutch solenoid valve
• Control valve assembly
Selector lever
: D position
Gear
: 4GR
Stop lamp switch
: OFF
Vehicle speed
: 20 km/h (13 MPH) or more
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст