Nissan Versa Sedan. Instruction — part 428
HIGH-MOUNTED STOP LAMP
EXL-113
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Removal
1. Fully open trunk lid assembly.
2. Rotate the bulb socket counterclockwise.
3. Release high-mounted stop lamp pawls and remove high-mounted stop lamp housing.
Installation
Installation is in the reverse order of removal.
Bulb Replacement
INFOID:0000000009269686
WARNING:
Do not touch bulb with your hand while it is on or right after being turned off. Burning may result.
CAUTION:
• Do not touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-
vent damage to the bulb.
• Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HIGH-MOUNTED STOP LAMP BULB - REAR SPOILER
The high-mounted stop lamp bulb is a LED and is integrated into the high-mounted stop lamp and is serviced
as an assembly. Refer to
EXL-112, "Removal and Installation"
HIGH-MOUNTED STOP LAMP BULB - PARCEL SHELF
Removal
1. Fully open trunk lid assembly.
2. Rotate the bulb socket counterclockwise and remove.
3. Remove the bulb from the bulb socket.
Installation
Installation is in the reverse order of removal.
EXL-114
< REMOVAL AND INSTALLATION >
LICENSE PLATE LAMP
LICENSE PLATE LAMP
Exploded View
INFOID:0000000009269687
Removal and Installation
INFOID:0000000009269688
REMOVAL
1. While pressing the license plate lamp housing pawl toward the right, pull the housing downward and
remove.
2. Rotate the bulb socket counterclockwise and remove.
3. Remove the license plate lamp.
INSTALLATION
Installation is in the reverse order of removal.
Bulb Replacement
INFOID:0000000009269689
WARNING:
Do not touch bulb with your hand while it is on or right after being turned off. Burning may result.
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse while performing the opera-
tion.
• After installing the bulb, install the back cover and the bulb socket securely for watertightness.
• Do not touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-
vent damage to the bulb.
• Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
LICENSE PLATE LAMP BULB
Removal
1. Remove the license plate lamp. Refer to
EXL-114, "Removal and Installation"
.
2. Remove the bulb from the socket.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, install the bulb socket securely for watertightness.
1.
License plate lamp
2.
License plate lamp bulb
JMLIA2055ZZ
SERVICE DATA AND SPECIFICATIONS (SDS)
EXL-115
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Bulb Specifications
INFOID:0000000009269690
*: Always check with the Parts Department for the latest parts information.
Item
Wattage (W)*
Front combination lamp
High beam
60
Low beam
55
Turn signal/Park lamp
28/8
Side marker lamp
5
Front fog lamp (if equipped)
55
Rear combination lamp
Stop/Tail lamp
21/5
Turn signal lamp
21
Back-up lamp
21
License plate lamp
5
High-mounted stop lamp
16
EXT-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D
E
F
G
H
I
J
L
M
SECTION
EXT
A
B
EXT
N
O
P
CONTENTS
EXTERIOR
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Procedure without Cowl Top Cover . ..
Precaution for Work . . . . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . . ..
Commercial Service Tools . . . . . . . . . ...
CLIP LIST . . . . . . . . . . . . . . .
Descriptions for Clips . . . . . . . . . . . ....
SYMPTOM DIAGNOSIS . . . . . . . ...
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES . . . . . . . . . . . . . . . .
Work Flow . . . . . . . . . . . . . . . .....
Generic Squeak and Rattle Troubleshooting . . ..
Diagnostic Worksheet . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
FRONT BUMPER . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
UNDER COVER . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
REAR BUMPER . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
FRONT GRILLE . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
COWL TOP . . . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
FENDER PROTECTOR . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
ROOF SIDE MOLDING . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
DOOR OUTSIDE MOLDING . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
TRUNK LID FINISHER . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
DOOR PARTING SEAL . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
REAR SPOILER . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст