Nissan Versa Sedan. Instruction — part 808
TM-138
< DTC/CIRCUIT DIAGNOSIS >
[4AT: RE4F03C]
U1117 LOST COMMUNICATION (ABS)
U1117 LOST COMMUNICATION (ABS)
DTC Logic
INFOID:0000000009267895
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn the ignition switch OFF and wait for
at least 10 seconds, then perform the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON, and wait for 5 seconds or more.
2. Check the DTC.
Is “U1117” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009267896
For the diagnosis procedure, refer to
LAN-15, "Trouble Diagnosis Flow Chart"
DTC
Trouble diagnosis name
DTC detecting condition
Possible causes
U1117
Lost Communication With ABS
When the ignition switch is ON,
TCM is unable to receive the
CAN communications signal
from ABS actuator control unit
continuously for 2 seconds or
more.
• ABS actuator & control mod-
ule
• Harness or connector
(CAN communication line is
open or shorted)
P062F EEPROM
TM-139
< DTC/CIRCUIT DIAGNOSIS >
[4AT: RE4F03C]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P062F EEPROM
Description
INFOID:0000000009267897
TCM checks the value read in FLASH ROM at ignition switch ON, and judges if there is writing failure to
FLASH ROM or malfunction of FLASH ROM.
DTC Logic
INFOID:0000000009267898
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn the ignition switch OFF and wait for
at least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1. Shift the selector lever to the P position.
2. Start engine.
3. Check the first trip DTC.
Is “P062F” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009267899
1.
PERFORM DTC CONFIRMATION PROCEDURE
GI-45, "Intermittent Incident"
.
Is the inspection result normal?
YES
TM-241, "Removal and Installation"
.
NO
>> Repair or replace damaged parts.
DTC
Trouble diagnosis name
DTC detection condition
Possible causes
P062F
Internal Control Module EE-
PROM Error
When the ignition switch is ON,
an error detected is the memory
back-up value from the TCM
FLASH ROM.
Control valve ASSY (ROM-as-
sembly)
TM-140
< DTC/CIRCUIT DIAGNOSIS >
[4AT: RE4F03C]
P0705 TRANSMISSION RANGE SWITCH A
P0705 TRANSMISSION RANGE SWITCH A
DTC Logic
INFOID:0000000009267900
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn the ignition switch OFF and wait for
at least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1. Turn ignition switch ON.
2. Shift the selector lever to the entire position from P to 1. (Hold the selector lever at each position for 10
seconds or more.)
3. Check the first trip DTC.
Is “P0705” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009267901
1.
CHECK TCM INPUT SIGNALS
With CONSULT
1. Turn ignition switch ON.
2. Select “TRANSMISSION” “DATA MONITOR”.
3. Select the “D position switch”, “N position switch”, “R position switch”, “P position switch”, “2 position
switch”, and “1 position switch”.
4. Shift the selector lever to the entire position from P to 1, and check the ON/OFF operation of each monitor
item.
DTC
Trouble diagnosis name
DTC detection condition
Possible causes
P0705
Transmission Range Sensor
“A” Circuit Malfunction (PRNDL
input)
The following diagnosis condi-
tions are met and 2 or more po-
sition signals are ON at the
same time for 5 seconds or
more.
• Diagnosis condition
- TCM power supply voltage:
10 V <TCM power supply
voltage <16 V
• Harness or connector
(Short circuit between trans-
mission position SW and
TCM)
• Transmission range switch
Monitor item
Condition
Status
RANGE SW 1
Selector lever in “1” position
On
Other than the above
Off
RANGE SW 2
Selector lever in “2” position
On
Other than the above
Off
RANGE SW D
Selector lever in “D” position
On
Other than the above
Off
RANGE SW N
Selector lever in “N” position
On
Other than the above
Off
RANGE SW R
Selector lever in “R” position
On
Other than the above
Off
P0705 TRANSMISSION RANGE SWITCH A
TM-141
< DTC/CIRCUIT DIAGNOSIS >
[4AT: RE4F03C]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Without CONSULT.
1. Turn ignition switch OFF.
2. Disconnect the TCM connector.
3. Turn ignition switch ON.
4. Shift the selector lever to the entire position from P to 1, and check the voltage between the TCM harness
connector terminal and ground.
Is the check result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO-1 [D position SW is “On” when selector is not in D position. (Or, connector terminal 4 is at 10 - 16 V.)]>>
GO TO 2.
NO-2 [N position SW is “On” when selector is not in N position. (Or, connector terminal 5 is at 10 - 16 V.)]>>
GO TO 4.
NO-3 [R position SW is “On” when selector is not in R position. (Or, connector terminal 6 is at 10 - 16 V.)]>>
GO TO 6.
NO-4 [P position SW is “On” when selector is not in P position. (Or, connector terminal 7 is at 10 - 16 V.)]>>
GO TO 8.
NO-5 [2 position SW is “On” when selector is not in 2 position. (Or, connector terminal 3 is at 10 - 16 V.)]>>
GO TO 10.
NO-6 [1 position SW is “On” when selector is not in 1 position. (Or, connector terminal 2 is at 10 - 16 V.)]>>
GO TO 12.
2.
CHECK D POSITION SW CIRCUIT (CHECK 1)
1. Turn ignition switch OFF.
2. Disconnect the TCM connector.
3. Check the continuity between the TCM harness connector terminals.
RANGE SW P
Selector lever in “P” position
On
Other than the above
Off
Monitor item
Condition
Status
TCM harness connector
Ground
Condition
Voltage
Connector
Terminal
F44
2
Ground
Selector lever in “1” posi-
tion
10 - 16 V
Other than the above
Approx. 0 V
3
Selector lever in “2” posi-
tion
10 - 16 V
Other than the above
Approx. 0 V
4
Selector lever in “D” po-
sition
10 - 16 V
Other than the above
Approx. 0 V
5
Selector lever in “N” po-
sition
10 - 16 V
Other than the above
Approx. 0 V
6
Selector lever in “R” po-
sition
10 - 16 V
Other than the above
Approx. 0 V
7
Selector lever in “P” posi-
tion
10 - 16 V
Other than the above
Approx. 0 V
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст