Nissan Versa Sedan. Instruction — part 627
PCS-94
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
B26F6 BCM
Is the inspection result normal?
YES
>> Refer to
GI-45, "Intermittent Incident"
.
NO
>> Replace BCM. Refer to
PCS
PUSH-BUTTON IGNITION SWITCH
PCS-95
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
PUSH-BUTTON IGNITION SWITCH
Component Function Check
INFOID:0000000009266488
1.
CHECK FUNCTION
1. Select “PUSH SW” in “Data Monitor” of BCM with CONSULT.
2. Check the push-button ignition switch signal under the following conditions.
Is the indication normal?
YES
>> Inspection End.
NO
Diagnosis Procedure
INFOID:0000000009266489
Regarding Wiring Diagram information, refer to
.
1.
CHECK PUSH-BUTTON IGNITION SWITCH OUTPUT SIGNAL (PUSH-BUTTON IGNITION SWITCH)
1. Turn ignition switch OFF.
2. Disconnect push-button ignition switch connector and IPDM E/R connector E47.
3. Check voltage between push-button ignition switch connector M25 terminal 8 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT (BCM)
1. Disconnect BCM connector M98.
2. Check continuity between BCM connector M98 terminal 76 and push-button ignition switch connector
M25 terminal 8.
3. Check continuity between BCM connector M98 terminal 76 and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-69, "Removal and Installation"
NO
>> Repair or replace harness or connectors.
3.
CHECK IGNITION SWITCH OUTPUT SIGNAL (IPDM E/R)
Check voltage between IPDM E/R connector E47 terminal 81 and ground.
Test item
Condition
Status
PUSH SW
Push-button ignition switch is pressed
On
Push-button ignition switch is not pressed
Off
Push-button ignition switch
Ground
Voltage
(Approx.)
Connector
Terminal
M25
8
—
Battery voltage
BCM
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
M98
76
M25
8
Yes
BCM
Ground
Continuity
Connector
Terminal
M98
76
—
No
PCS-96
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
PUSH-BUTTON IGNITION SWITCH
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT (IPDM E/R)
1. Disconnect BCM connector M17.
2. Check continuity between IPDM E/R connector E47 terminal 81 and push-button ignition switch connector
M25 terminal 8.
3. Check continuity between IPDM E/R connector E47 terminal 81 and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-30, "Removal and Installation"
NO
>> Repair or replace harness or connectors.
5.
CHECK PUSH-BUTTON IGNITION SWITCH GROUND CIRCUIT
Check continuity between push-button ignition switch connector M25 terminal 4 and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness or connectors.
6.
CHECK PUSH-BUTTON IGNITION SWITCH
PCS-96, "Component Inspection"
.
Is the inspection result normal?
YES
>> Refer to
GI-45, "Intermittent Incident"
.
NO
>> Replace push-button ignition switch.
Component Inspection
INFOID:0000000009266490
1.
CHECK PUSH-BUTTON IGNITION SWITCH
1. Turn ignition switch OFF.
2. Disconnect push-button ignition switch connector.
3. Check continuity between push-button ignition switch terminals.
Is the inspection result normal?
IPDM E/R
Ground
Voltage
(Approx.)
Connector
Terminal
E47
81
—
Battery voltage
IPDM E/R
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
E47
81
M25
8
Yes
IPDM E/R
Ground
Continuity
Connector
Terminal
E47
81
—
No
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M25
4
—
Yes
Push-button ignition switch terminals
Condition
Continuity
4 – 8
Pressed
Yes
Not pressed
No
PCS
PUSH-BUTTON IGNITION SWITCH
PCS-97
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
YES
>> Inspection End.
NO
>> Replace push-button ignition switch.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст