Nissan Versa Sedan. Instruction — part 425
FRONT FOG LAMP AIMING ADJUSTMENT
EXL-101
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
FRONT FOG LAMP AIMING ADJUSTMENT
Inspection
INFOID:0000000009269667
PREPARATION BEFORE ADJUSTING
CAUTION:
Do not use organic solvent (thinner, gasoline etc.)
NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the front fog lamp has been replaced.
• Before performing aiming adjustment, check the following.
• Keep all tires inflated to correct pressure.
• Place vehicle on level ground.
• See that vehicle is unloaded (except for full levels of coolant, engine oil and fuel, and spare tire, jack, and
tools). Have the driver or equivalent weight placed in driver seat.
• Adjust aiming in the vertical direction by turning the adjusting screw.
• When performing adjustment, if necessary, cover the headlamps and opposite fog lamp.
AIMING ADJUSTMENT SCREW
• Turn the aiming adjusting screw using a suitable tool to aim the fog
lamp.
A: UP
B: DOWN
• For the position and direction of the adjusting screw refer to the fig-
ure as shown.
Aiming Adjustment Procedure
INFOID:0000000009269668
1. Screen placement.
NOTE:
• Place the screen perpendicular to the level road.
• Position the vehicle facing the screen with 10 m (32.8 ft) between the front fog lamp center and the
screen.
2. Start the engine. Illuminate the front fog lamp.
CAUTION:
Do not cover the lens surface with a tape etc. The lens are made of resin.
3. Adjust the cutoff line height (A) with the aiming adjustment
screw so that the distance (X) between the horizontal center line
of front fog lamp (H) and (A) becomes 200 mm (7.87 in).
Front fog lamp light distribution on the screen
• A :Cutoff line
• B :High illuminance
• H :Horizontal center line of front fog lamp
• V :Vertical center line of front fog lamp
• X :Cutoff line height
JMLIA2040ZZ
JPLIA0008ZZ
EXL-102
< REMOVAL AND INSTALLATION >
FRONT COMBINATION LAMP
REMOVAL AND INSTALLATION
FRONT COMBINATION LAMP
Exploded View
INFOID:0000000009269669
Removal and Installation
INFOID:0000000009269670
REMOVAL
1. Disconnect the battery negative terminal. Refer to
PG-63, "Removal and Installation"
2. Remove front bumper fascia. Refer to
EXT-16, "Removal and Installation"
.
3. Remove the front combination lamp bolts.
4. Pull the headlamp assembly forward slightly.
5. Disconnect the harness connectors from the front combination lamp and remove.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
After installation, perform headlamp aiming adjustment procedure. Refer to
EXL-99, "Aiming Adjustment Pro-
Bulb Replacement
INFOID:0000000009269671
WARNING:
Do not touch bulb with your hand while it is on or right after being turned off. Burning may result.
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse while performing the opera-
tion.
• Do not touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-
vent damage to the bulb.
• Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB
Removal
1. Disconnect the harness connector from the headlamp bulb.
2. Remove the cover.
1.
Front combination lamp (LH)
JMLIA2041GB
FRONT COMBINATION LAMP
EXL-103
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
3. Remove the retaining spring lock and the bulb from the front combination lamp.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, install the bulb socket securely for watertightness.
PARKING LAMP BULB
Removal
1. Rotate the bulb socket counterclockwise and remove.
2. Remove the bulb from the bulb socket.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, install the bulb socket securely for watertightness.
FRONT TURN SIGNAL LAMP BULB
Removal
1. Rotate the bulb socket counterclockwise and remove.
2. Remove the bulb from the bulb socket.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, install the bulb socket securely for watertightness.
Disassembly and Assembly
INFOID:0000000009269672
Exploded View
WARNING:
Do not touch bulb with your hand while it is on or right after being turned off. Burning may result.
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse while performing the opera-
tion.
• After installing the bulb, install cover and the bulb socket securely for watertightness.
• Do not touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-
vent damage to the bulb.
1.
Front combination lamp
2.
Parking lamp bulb
3.
Parking lamp bulb socket
4.
Cover
5.
Halogen bulb
6.
Front turn signal lamp bulb socket
7.
Front turn signal lamp bulb
8.
Retaining spring
JMLIA2042ZZ
EXL-104
< REMOVAL AND INSTALLATION >
FRONT COMBINATION LAMP
• Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
DISASSEMBLY
1. Remove the cover.
2. Remove the retaining spring lock and bulb.
3. Rotate the parking lamp bulb socket counterclockwise and remove.
4. Remove the bulb from the parking lamp bulb socket.
5. Rotate the front turn signal lamp bulb socket counterclockwise and remove.
6. Remove the bulb from the front turn signal lamp bulb socket.
ASSEMBLY
Assembly is in the reverse order of disassembly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст