Nissan Versa Sedan. Instruction — part 676
SE-30
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
4. Release the J-hook retainer (C), unzip seatback zipper (A) and
release J-clips (B) holding the seatback trim to the seat frame
assembly.
5. Reach up through the seatback trim and release locks as shown
and remove the headrest holders (if equipped).
CAUTION:
Before removing/installing the headrest holder, check its
orientation (front/rear and right/left)
6. Remove and discard the two chute rod nuts (B), then route the
chute rod (1) through the opening and remove it from the chute
(A).
CAUTION:
Do not reuse the chute rod nuts.
7. Release the side air bag module harness from the seat frame
assembly.
NOTE:
Take note of harness routing and attachment location for accu-
rate installation.
a. From the back of the seat unclip the side air bag module har-
ness clips (
).
b. From the bottom of the seat unclip the side air bag module har-
ness clips (
).
ALJIA0987ZZ
PIIB4084J
ALJIA0992ZZ
ALJIA0689ZZ
ALJIA0692ZZ
FRONT SEAT
SE-31
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
8. Remove and discard the two side air bag module nuts (A).
CAUTION:
Do not reuse the side air bag module nuts.
9. Disengage the side air bag module studs from the seatback frame and lift the seatback trim and seatback
pad as an assembly from the seat frame assembly.
10. Pull the side air bag module (1) out of the chute (A) and remove
from the seatback trim.
CAUTION:
• Replace the side air bag module if it has been dropped or
sustained an impact.
• Do not strike the side air bag module.
11. Separate the seatback trim from the seatback pad.
a. For seatback with removable headrest.
i.
Remove the hog rings and separate the seatback trim (1) from
the seatback pad.
: Hog ring
NOTE:
Remove all pieces of hog rings and discard them.
ALJIA0991ZZ
ALJIA0993ZZ
JMHIA0009ZZ
ALJIA0988ZZ
SE-32
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
b. For seatback without removable headrest.
i.
Remove the hog rings and separate the seatback trim (1) from
the seatback pad.
: Hog ring
NOTE:
Remove all pieces of hog rings and discard them.
Assembly
Assembly is in the reverse order of disassembly.
• Tighten the side air bag module nuts to specification. Refer to
SE-26, "DRIVER SIDE : Exploded View"
CAUTION:
Do not reuse the side air bag module nuts.
• Tighten the chute rod nuts to specification. Refer to
SE-26, "DRIVER SIDE : Exploded View"
.
CAUTION:
Do not reuse the chute rod nuts.
CAUTION:
• Inspect seatback pad, seatback trim and seatback trim chutes. Replace if damaged.
• Smooth out all wrinkles during assembly.
• Always route side air bag module harness in original location. Replace any deformed or damaged
clips with same type and color. Always install clips in the original location in the harness.
• After work is completed, check that no system malfunction is detected causing the air bag warning
lamp to illuminate.
• If a malfunction is detected by the air bag warning lamp after repair or replacement of the malfunc-
tion parts, perform the SRS final check. Refer to
.
• Install new hog rings on the seatback trim in original positions.
Use only one hog ring in each designated location.
Ensure hog rings are correctly fastened around both the seatback
trim and seatback pad wires.
Use NISSAN standard hog rings and tools to assemble.
SEAT CUSHION
WARNING:
Do not leave any objects (screwdrivers, tools, etc.) on the seat during seat cushion repair. It can lead
to personal injury if the side air bag should accidentally deploy.
CAUTION:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least three
minutes.
• Always work from the side or back of the seatback assembly, do not work in front of seat.
• Do not use air tools or electric tools for servicing the seat assembly.
• During disassembly, do not damage the seatback cover, chutes, connectors, retainers, clips, module
harness or the side air bag module.
Disassembly
1. Remove the front seat assembly. Refer to
SE-17, "DRIVER SIDE : Removal and Installation"
2. Remove the lift lever.
ALJIA0989ZZ
PIIB3356J
FRONT SEAT
SE-33
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
a. Release pawls and remove the lift lever cap (1) (if equipped).
b. Remove screws and the lift lever (2) (if equipped).
: Pawl
3. Remove the recline lever.
a. Remove snap ring (1) using a suitable tool, then the recline lever
(2).
4. Remove the seat cushion outer finisher (LH).
a. Remove the screw (A).
b. Release the metal clips, then remove the seat cushion outer fin-
isher (LH) (1).
: Metal clip
5. Remove the seat belt buckle.
a. Unclip the seat belt buckle harness clip and connector clip from seat frame assembly.
b. Remove the seat belt buckle anchor bolt and the seat belt buckle.
6. Remove the seat cushion outer finisher (RH).
a. Remove the screw (B).
b. Lift up seat cushion trim (A).
c. Slide seat cushion outer finisher (RH) (1) rearward to release
pawl and remove.
: Pawl
7. Remove the seat cushion assembly from the seat frame assembly.
AWJIA0932ZZ
JMJIA6005ZZ
JMJIA6006ZZ
AWJIA0933ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст