Nissan Versa Sedan. Instruction — part 384
OIL SEAL
EM-71
< REMOVAL AND INSTALLATION >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
FRONT OIL SEAL : Removal and Installation
INFOID:0000000009266663
REMOVAL
1. Remove the following parts.
• Remove wheel and tire. Refer to
• Front fender protector (RH). Refer to
EXT-26, "Removal and Installation"
• Drive belt. Refer to
EM-16, "Removal and Installation"
• Crankshaft pulley. Refer to
.
2. Remove front oil seal with a suitable tool.
CAUTION:
Be careful not to damage front cover and crankshaft.
INSTALLATION
1. Apply new engine oil to new front oil seal joint surface and seal lip.
2. Install front oil seal so that each seal lip is oriented as shown.
• Press-fit front oil seal using a suitable drift with outer diameter 50 mm (1.97 in) and inner diameter 44
mm (1.73 in).
CAUTION:
• Be careful not to damage front cover and crankshaft.
• Press-fit oil seal straight to avoid causing burrs or tilting.
3. Installation of the remaining components is in the reverse order of removal.
REAR OIL SEAL
REAR OIL SEAL : Removal and Installation
INFOID:0000000009266664
REMOVAL
1. Remove transaxle assembly. Refer to
TM-27, "Removal and Installation"
(M/T models),
(A/T models),
TM-452, "Removal and Installation"
(CVT models).
2. Remove clutch cover and clutch disk (M/T models). Refer to
CL-18, "Removal and Installation"
3. Remove flywheel (M/T models) or drive plate (A/T or CVT models). Refer to
.
4. Remove rear oil seal with a suitable tool.
CAUTION:
Be careful not to damage crankshaft and cylinder block.
INSTALLATION
1. Apply the liquid gasket lightly to entire outside area of new rear oil seal.
Use Genuine Silicone RTV Sealant or equivalent. Refer to
GI-21, "Recommended Chemical Products
(A)
: Dust seal lip
(B)
: Oil seal lip
: Engine outside
: Engine inside
PBIC3485J
EM-72
< REMOVAL AND INSTALLATION >
[HR16DE]
OIL SEAL
2. Install rear oil seal so that each seal lip is oriented as shown.
• Press-fit rear oil seal with a suitable drift (A) outer diameter
113 mm (4.45 in) and inner diameter 90 mm (3.54 in).
CAUTION:
• Be careful not to damage crankshaft and cylinder block.
• Press-fit oil seal straight to avoid causing burrs or tilt-
ing.
• Do not touch grease applied onto oil seal lip.
• Press in rear oil seal (1) to the position as shown.
3. Installation of the remaining components is in the reverse order of removal.
(A)
: Dust seal lip
(B)
: Oil seal lip
: Engine outside
: Engine inside
PBIC3485J
PBIC3660E
(A)
: Rear end surface of cylinder block
(b)
: 0 - 0.5 mm (0 - 0.020 in)
PBIC3149J
CYLINDER HEAD
EM-73
< REMOVAL AND INSTALLATION >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
CYLINDER HEAD
Exploded View
INFOID:0000000009266665
Cylinder Head Bolts
Valve Components
JPBIA4097ZZ
1.
Cylinder head assembly
2.
Cylinder head bolt
3.
Washer
4.
Cylinder head gasket
A. Refer to
JPBIA4098GB
1.
Spark plug
2.
Valve collet
3.
Valve spring retainer
4.
Valve spring
5.
Valve spring seat
6.
Valve oil seal
EM-74
< REMOVAL AND INSTALLATION >
[HR16DE]
CYLINDER HEAD
Removal and Installation
INFOID:0000000009266666
REMOVAL
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Release fuel pressure. Refer to
2. Remove the following components and related parts.
• Air duct. Refer to
EM-25, "Removal and Installation"
• Fuel tube and fuel injector. Refer to
.
• Water outlet. Refer to
CO-25, "Removal and Installation"
• Exhaust manifold. Refer to
• Front cover and timing chain. Refer to
.
• Camshaft. Refer to
.
3. Remove cylinder head loosening bolts in reverse order as
shown.
4. Remove cylinder head gasket.
INSTALLATION
1. Install new cylinder head gasket.
2. Tighten cylinder head bolts in numerical order as shown.
CAUTION:
If cylinder head bolts are reused, check their outer diame-
ters before installation. Refer to
a. Apply new engine oil to threads and seating surfaces of bolts.
b. Tighten all bolts.
7.
Valve guide (INT)
8.
Valve guide (EXH)
9.
Valve seat (EXH)
10. Valve (EXH)
11. Valve (INT)
12. Valve seat (INT)
A.
(A) : EXH side
(B) : INT side
: Engine front
PBIC3732E
(A) : EXH side
(B) : INT side
: Engine front
Cylinder head bolts
: 40.0 N·m (4.1 kg-m, 30 ft-lb)
PBIC3732E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст