Nissan Versa Sedan. Instruction — part 710
SEC-112
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
SYSTEM
• The key registration is a procedure that erases the current NATS ID once, and then re-registers a new ID.
Therefore the registered key is necessary for this procedure. Before starting the registration procedure, col-
lect all registered Keys from the customer.
• The NATS ID registration is the procedure that registers the ID stored into the transponder (integrated in
mechanical key) to BCM.
The key ID registration is the procedure that registers the ID to the BCM.
• When performing the key system registration only, the engine cannot be started by inserting the key into the
key cylinder. When performing the NATS registration only, the engine cannot be started by using the ignition
key.
SECURITY INDICATOR
• Always flashes with ignition key in the OFF position.
MAINTENANCE INFORMATION
CAUTION:
It is necessary to perform NATS ID registration when replacing any of the following part.
If it's not (or fail to do so), the electrical system may not operate properly.
• BCM
• ECM
• IPDM E/R
• Ignition key
• NATS antenna amp.
• Dongle unit
• Combination meter
DIAGNOSIS SYSTEM (BCM)
SEC-113
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000009541424
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
Direct Diagnostic Mode
Description
ECU identification
The BCM part number is displayed.
Self Diagnostic Result
The BCM self diagnostic results are displayed.
Data Monitor
The BCM input/output data is displayed in real time.
Active Test
The BCM activates outputs to test components.
Work support
The settings for BCM functions can be changed.
Configuration
• The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing BCM.
CAN DIAG SUPPORT MNTR
The result of transmit/receive diagnosis of CAN communication is displayed.
System
Sub System
Direct Diagnostic Mode
ECU id
en
tif
ica
tion
Se
lf Di
ag
no
st
ic
Res
u
lt
Dat
a
M
on
ito
r
Acti
ve
T
est
W
o
rk
su
pp
ort
Co
nf
ig
ur
at
io
n
CAN DIAG SUP
P
OR
T MNTR
Door lock
DOOR LOCK
×
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps FLASHER
×
×
Air conditioner
AIR CONDITIONER
×
Combination switch
COMB SW
×
BCM
BCM
×
×
×
×
×
Immobilizer
IMMU
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Trunk open
TRUNK
×
Vehicle security system
THEFT ALM
×
×
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
AIR PRESSURE MONITOR
×
×
×
×
Panic alarm system
PANIC ALARM
×
SEC-114
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
IMMU
IMMU : CONSULT Function (BCM - IMMU)
INFOID:0000000009541425
SELF DIAGNOSTIC RESULT
ACTIVE TEST
WORK SUPPORT
Test Item
Description
THEFT IND
This test is able to check security indicator operation [On/Off].
Support Item
Setting
Description
CONFIRM DONGLE ID
—
Dongle ID code can be read.
DIAGNOSIS SYSTEM (IPDM E/R)
SEC-115
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
DIAGNOSIS SYSTEM (IPDM E/R)
Diagnosis Description
INFOID:0000000009541426
AUTO ACTIVE TEST
Description
In auto active test, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Front wiper (LO, HI)
• Parking lamp
• License plate lamp
• Tail lamp
• Front fog lamp
• Headlamp (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan
Operation Procedure
NOTE:
Never perform auto active test in the following conditions.
• Passenger door is open
• CONSULT is connected
1. Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper
operation)
NOTE:
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.
2. Turn the ignition switch OFF.
3. Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF.
4. Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.
5. After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
• When auto active test has to be cancelled halfway through test, turn the ignition switch OFF.
• When auto active test is not activated, door switch may be the cause. Check door switch. Refer to
Inspection in Auto Active Test
When auto active test is actuated, the following operation sequence is repeated 3 times.
Operation se-
quence
Inspection location
Operation
1
Front wiper
LO for 5 seconds
→ HI for 5 seconds
2
• Parking lamp
• License plate lamp
• Tail lamp
• Front fog lamp
10 seconds
3
Headlamp
LO for 10 seconds
→HI ON ⇔ OFF 5 times
4
A/C compressor (magnet clutch)
ON
⇔ OFF 5 times
5
Cooling fan
LO for 5 seconds
→ MID for 3 seconds → HI for 2 seconds
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст