Nissan Versa Sedan. Instruction — part 924
WW-46
< REMOVAL AND INSTALLATION >
FRONT WIPER
1. Lift up wiper arm and set to the position where wiper arm can be locked back.
2. Press and hold lever (A) of wiper blade (1). Pull in the direction
indicated by the arrow as shown and remove wiper blade from
wiper arm (2).
CAUTION:
Wrap wiper arm using a shop cloth so that wiper blade does
not damage windshield glass.
INSTALLATION
Installation is in the reverse order of removal.
WIPER REFILL
WIPER REFILL : Removal and Installation
INFOID:0000000009269580
REMOVAL
1. Remove wiper blade from the wiper arm. Refer to
WW-45, "WIPER BLADE : Removal and Installation"
.
2. From portion (A) of wiper refill (1), disengage wiper blade portion
(B) and remove wiper refill in the direction indicated by the arrow
as shown.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• For installation of wiper refill, check that wiper refill was not twisted while installing.
• Check that wiper refill was inserted normally from the correct direction.
WIPER DRIVE ASSEMBLY
WIPER DRIVE ASSEMBLY : Removal and Installation
INFOID:0000000009269581
EXPLODED VIEW
JMLIA1990ZZ
JMLIA1992ZZ
FRONT WIPER
WW-47
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
REMOVAL
1. Remove cowl top cover. Refer to
EXT-24, "Removal and Installation"
.
2. Disconnect the harness connector from the wiper motor.
3. Remove the wiper drive assembly bolts.
4. Remove wiper drive assembly from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
WIPER DRIVE ASSEMBLY : Disassembly and Assembly
INFOID:0000000009269582
EXPLODED VIEW
1.
Wiper arm cap
2.
Wiper arm (LH)
3.
Wiper blade (LH)
4.
Wiper refill (LH)
5.
Wiper arm (RH)
6.
Wiper blade (RH)
7.
Wiper refill (RH)
8.
Wiper drive assembly
AWLIA1893ZZ
WW-48
< REMOVAL AND INSTALLATION >
FRONT WIPER
DISASSEMBLY
1. Remove wiper linkage 1 and wiper linkage 2 from the wiper frame.
CAUTION:
Do not bend the linkage or damage the plastic part of the ball joint when removing the wiper link-
age.
2. Remove wiper motor screws.
3. Remove the wiper motor from the wiper frame.
ASSEMBLY
1. Connect the harness connector to the wiper motor.
2. Operate wiper to move it to the auto stop position.
3. Disconnect the harness connector from the wiper motor.
4. Install wiper motor to wiper frame.
5. Install wiper linkage 1 to the wiper motor and the wiper frame.
6. Install wiper linkage 2 to the wiper frame.
CAUTION:
• Do not drop wiper motor or cause it to come into contact with other parts.
• Be careful of the grease condition at the wiper motor and wiper linkage joint (retainer). Apply
multi
−purpose grease or an equivalent if necessary.
1.
Shaft seal
2.
Wiper frame
3.
Wiper linkage 1
4.
Wiper linkage 2
5.
Wiper motor assembly
6.
Wiper motor assembly bracket
AWLIA1894ZZ
WASHER TANK
WW-49
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WASHER TANK
Exploded View
INFOID:0000000009269583
Removal and Installation
INFOID:0000000009269584
REMOVAL
1. Remove fender protector. Refer to
EXT-26, "Removal and Installation"
2. Disconnect the harness connector from the washer pump.
3. Remove front washer tube.
4. Remove washer tank assembly bolts.
5. Remove washer tank assembly from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
• After installation, add water to the top of the washer tank inlet to check that no leaks exist.
• Fill washer tank with specified amount of fluid. Refer to
1.
Washer tank inlet cap
2.
Washer tank assembly
Front
JMLIA2076GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст