Nissan Versa Sedan. Instruction — part 869
TM-382
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
P0962 PRESSURE CONTROL SOLENOID A
P0962 PRESSURE CONTROL SOLENOID A
DTC Logic
INFOID:0000000009268189
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1. Start the engine and wait for 5 seconds or more.
2. Check the first trip DTC.
Is “P0962” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009268190
1.
CHECK CIRCUIT BETWEEN TCM AND CVT UNIT
1. Turn ignition switch OFF.
2. Disconnect TCM connector and CVT unit connector.
3. Check continuity between TCM harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning parts.
2.
CHECK LINE PRESSURE SOLENOID VALVE
Check line pressure solenoid valve. Refer to
TM-382, "Component Inspection (Line Pressure Solenoid
.
Is the inspection result normal?
YES >> Check
intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
Component Inspection (Line Pressure Solenoid Valve)
INFOID:0000000009268191
1.
CHECK LINE PRESSURE SOLENOID VALVE
Check resistance between CVT unit connector terminal and ground.
DTC
Trouble diagnosis name
DTC detection condition
Possible causes
P0962
Pressure Control Solenoid A
Control Circuit Low
The line pressure solenoid valve current is
200 mA or less continuously for 200 msec or
more under the following diagnosis condi-
tions:
• Diagnosis conditions
- Solenoid output current: 750 mA or more
- GND short diagnosis of the solenoid drive
circuit is satisfied.
- TCM power supply voltage: More than 11 V
• Harness or connector
(Line pressure solenoid valve circuit is
shorted to ground)
• Line pressure solenoid valve
TCM
Ground
Continuity
Connector
Terminal
F44
30
Ground
Not existed
P0962 PRESSURE CONTROL SOLENOID A
TM-383
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> There is a malfunction of line pressure solenoid valve. Replace transaxle assembly. Refer to
452, "Removal and Installation"
CVT unit
Ground
Condition
Resistance
Terminal
2
Ground
CVT fluid temperature: 20
°C (68°F)
Approx. 5.3
Ω
CVT fluid temperature: 50
°C (122°F)
Approx. 6.0
Ω
CVT fluid temperature: 80
°C (176°F)
Approx. 6.7
Ω
TM-384
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
P0963 PRESSURE CONTROL SOLENOID A
P0963 PRESSURE CONTROL SOLENOID A
DTC Logic
INFOID:0000000009268192
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1. Start the engine and wait for 5 seconds or more.
2. Check the first trip DTC.
Is “P0963” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009268193
1.
CHECK CIRCUIT BETWEEN TCM AND CVT UNIT
1. Turn ignition switch OFF.
2. Disconnect TCM connector and CVT unit connector.
3. Check continuity between TCM harness connector terminal and CVT unit harness connector terminal.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning parts.
2.
CHECK LINE PRESSURE SOLENOID VALVE
Check line pressure solenoid valve. Refer to
TM-384, "Component Inspection (Line Pressure Solenoid
.
Is the inspection result normal?
YES >> Check
intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
Component Inspection (Line Pressure Solenoid Valve)
INFOID:0000000009268194
1.
CHECK LINE PRESSURE SOLENOID VALVE
Check resistance between CVT unit connector terminal and ground.
DTC
Trouble diagnosis name
DTC detection condition
Possible causes
P0963
Pressure Control Solenoid A
Control Circuit High
The line pressure solenoid valve current is
200 mA or less continuously for 200 msec or
more under the following diagnosis condi-
tions:
• Diagnosis conditions
- Solenoid output current: 750 mA or more
- GND short diagnosis of the solenoid drive
circuit is not satisfied.
- TCM power supply voltage: More than 11 V
• Harness or connector
(Line pressure solenoid valve circuit is
open or shorted to power supply)
• Line pressure solenoid valve
TCM
CVT unit
Continuity
Connector
Terminal
Connector
Terminal
F44
30
F46
2
Existed
P0963 PRESSURE CONTROL SOLENOID A
TM-385
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> There is a malfunction of line pressure solenoid valve. Replace transaxle assembly. Refer to
452, "Removal and Installation"
CVT unit
Ground
Condition
Resistance
Terminal
2
Ground
CVT fluid temperature: 20
°C (68°F)
Approx. 5.3
Ω
CVT fluid temperature: 50
°C (122°F)
Approx. 6.0
Ω
CVT fluid temperature: 80
°C (176°F)
Approx. 6.7
Ω
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст