Nissan Versa Sedan. Instruction — part 244
DLK-294
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
TRUNK LID
TRUNK LID ASSEMBLY : Adjustment
INFOID:0000000009269000
Check the clearance and surface height between trunk lid and each part by visual inspection and tactile feel.
If the clearance and surface height are out of specification, adjust them according to the adjustment proce-
dure.
Unit: mm (in)
1.
Trunk lid assembly
2.
Trunk lid hinge
3.
Trunk lid striker
4.
Body side outer
5.
Rear combination lamp
6.
Rear bumper fascia
JMKIA8147GB
Section
Item
Measurement
Standard
Difference (RH/LH,
MAX)
A – A
E
Clearance
3.5
± 1.0 (0.14 ± 0.04)
1.5 (0.06)
F
Surface height
0.0
± 1.0 (0.00 ± 0.04)
1.5 (0.06)
B – B
G
Clearance
3.5
± 1.0 (0.14 ± 0.04)
1.5 (0.06)
H
Surface height
-0.5
± 1.0 (0.02 ± 0.04)
1.5 (0.06)
TRUNK LID
DLK-295
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1. Loosen trunk lid hinge bolts (trunk lid side).
2. Remove trunk rear plate. Refer to
INT-32, "TRUNK REAR PLATE : Removal and Installation"
.
3. Loosen trunk lid striker bolts.
4. Lift up trunk lid approximately 100 – 150 mm (3.9 – 5.9 in) then close it lightly and check that it is engaged
firmly with trunk lid closed.
5. Check the clearance and surface height.
6. Tighten trunk lid hinge and trunk lid striker.
7. Install trunk rear plate. Refer to
INT-32, "TRUNK REAR PLATE : Removal and Installation"
.
TRUNK LID STRIKER ADJUSTMENT
Adjust trunk lid striker so that it becomes parallel with trunk lid lock insertion direction.
TRUNK LID STRIKER
TRUNK LID STRIKER : Removal and Installation
INFOID:0000000009269001
REMOVAL
1. Remove trunk rear plate. Refer to
INT-32, "TRUNK REAR PLATE : Removal and Installation"
.
2. Remove trunk lid opener cable bolt (A) and trunk lid striker bolts
(B).
3. Remove trunk lid striker (1), disconnect trunk lid opener cable
(2) from trunk lid striker and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check trunk lid open/close, lock/unlock operation.
• After installation, perform the trunk lid adjustment procedure. Refer to
.
TRUNK LID HINGE
C –C
I
Clearance
4.5
± 1.9 (0.18 ± 0.07)
2.9 (0.11)
J
Surface height
2.1
± 0.75 (0.08 ± 0.03)
3.0 (0.12)
D – D
K
Clearance
7.0
± 2.0 (0.28 ± 0.08)
2.5 (0.10)
Section
Item
Measurement
Standard
Difference (RH/LH,
MAX)
JMKIA8124ZZ
JMKIA8125ZZ
DLK-296
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
TRUNK LID
TRUNK LID HINGE : Removal and Installation
INFOID:0000000009269002
REMOVAL
1. Remove harness clips (A) from trunk lid hinge (RH only) (1).
2. Remove trunk lid assembly. Refer to
DLK-293, "TRUNK LID ASSEMBLY : Removal and Installation"
3. Remove torsion bar. Refer to
DLK-296, "TORSION BAR : Removal and Installation"
4. Remove rear parcel shelf finisher. Refer to
INT-25, "Removal and Installation"
5. Remove trunk lid hinge bolts (body side) and then trunk lid hinge.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check trunk lid open/close, lock/unlock operation.
• After installation, perform the trunk lid adjustment procedure. Refer to
.
• Apply touch-up paint (body color) onto the heads of trunk lid hinge bolts.
• Check trunk lid hinge rotating point for poor lubrication. If
necessary, apply a suitable multi-purpose grease.
TORSION BAR
TORSION BAR : Removal and Installation
INFOID:0000000009269003
REMOVAL
1. Remove torsion bar clamp.
2. Support trunk lid with a suitable tool.
WARNING:
Bodily injury may occur if trunk lid is not supported properly when removing the torsion bars.
JMKIA8126ZZ
JMKIA8127ZZ
TRUNK LID
DLK-297
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3. Apply a torsion bar wrench (A) to torsion bar (1) and lift torsion
bar to remove it.
NOTE:
For torsion bar wrench, refer to the figure.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Check trunk lid open/close operation after installation.
TRUNK LID WEATHER-STRIP
TRUNK LID WEATHER-STRIP : Removal and Installation
INFOID:0000000009269004
REMOVAL
Remove trunk lid weatherstrip from the trunk lid opening.
CAUTION:
Do not pull excessively on weatherstrip.
INSTALLATION
1. Working from the upper section, align weatherstrip center mark
(A) with vehicle center mark (B) and install weatherstrip onto the
vehicle.
: Front
JMKIA8128ZZ
PIIB3774J
JMKIA8129ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст