Nissan Versa Sedan. Instruction — part 262
SYSTEM
EC-47
< SYSTEM DESCRIPTION >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
BASIC ASCD SYSTEM
Automatic Speed Control Device (ASCD) allows a driver to keep vehicle at predetermined constant speed
without depressing accelerator pedal. Driver can be set the vehicle speed in the set speed range.
ECM controls throttle angle of electric throttle control actuator to regulate engine speed.
Operation status of ASCD is indicated in combination meter.
If any malfunction occurs in the ASCD system, it automatically deactivates the ASCD control.
EC-48, "AUTOMATIC SPEED CONTROL DEVICE (ASCD) : Switch Name and Function"
for ASCD
operating instructions.
CAUTION:
Always drive vehicle in a safe manner according to traffic conditions and obey all traffic laws.
ALTERNATOR POWER GENERATION VOLTAGE VARIABLE CONTROL SYS-
TEM
ALTERNATOR POWER GENERATION VOLTAGE VARIABLE CONTROL SYSTEM :
System Description
INFOID:0000000009640511
The alternator power generation voltage variable control system controls the amount of power generation,
according to a battery loaded condition. ECM judges a battery condition, according to a signal received from
the battery current sensor which detects a charge/discharge current. ECM then transmits a signal to IPDM E/
R to command power generation via CAN communication. IPDM E/R transmits a power generation control sig-
nal to the alternator so that the system can control the amount of power generation. The voltage of power gen-
eration is lowered during battery low-load conditions and boosted under heavy load conditions. In this way, the
system reduces the engine load through the adequate power generation control.
For details, refer to
.
EC-48
< SYSTEM DESCRIPTION >
[HR16DE]
OPERATION
OPERATION
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
AUTOMATIC SPEED CONTROL DEVICE (ASCD) : Switch Name and Function
INFOID:0000000009267011
SWITCHES AND INDICATORS
SET SPEED RANGE
ASCD system can be set the following vehicle speed.
SWITCH OPERATION
SET OPERATION
Press MAIN switch. (The CRUISE indicator in combination meter illuminates.)
When vehicle speed reaches a desired speed between approximately 38 km/h (24 MPH) and 144 km/h (90
MPH), press COAST/SET switch.
ACCELERATE OPERATION
If the ACCEL/RES switch is pressed during the cruise control driving, increase the vehicle speed until the
switch is released or vehicle speed reaches maximum speed controlled by the system.
And then ASCD will keep the new set speed.
CANCEL OPERATION
• When any of following conditions exist, the cruise operation is canceled.
- CANCEL switch is pressed
- ASCD MAIN switch is pressed (Set speed is cleared)
- More than 2 switches at ASCD steering switch are pressed at the same time (Set speed is cleared)
- Brake pedal is depressed
- Selector lever is changed to N, P or R position
- Vehicle speed decreased to 13 km/h (8 MPH) lower than the set speed
- TCS system is operated
1.
CRUISE indicator
2.
CANCEL switch
3.
ACCEL/RES switch
4.
COAST/SET switch
5.
ASCD MAIN switch
A.
On the combination meter
B.
On the steering wheel
JPBIA5708ZZ
Minimum speed (Approx.)
Maximum speed (Approx.)
38 km/h (24 MPH)
144 km/h (90 MPH)
Item
Function
CANCEL switch
Cancels the cruise control driving.
ACCEL/RES switch
• Resumes the set speed.
• Increases speed incrementally during cruise control driving.
COAST/SET switch
• Sets desired cruise speed.
• Decreases speed incrementally during cruise control driving.
ASCD MAIN switch
Master switch to activate the ASCD system.
OPERATION
EC-49
< SYSTEM DESCRIPTION >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
• When the ECM detects any of the following conditions, the ECM cancels the cruise operation and informs
the driver by blinking CRUISE indicator lamp.
- Engine coolant temperature is slightly higher than the normal operating temperature, CRUISE indicator lamp
is blinked slowly.
NOTE:
Engine coolant temperature decreases to the normal operating temperature, CRUISE indicator lamp stop
blinking and the cruise operation is able to work.
- Malfunction for some self-diagnoses regarding ASCD control: CRUISE indicator will blink quickly.
• When ASCD MAIN switch is turned to OFF during the cruise control driving, all of ASCD operations is can-
celed and vehicle speed memory is erased.
COAST OPERATION
When the COAST/SET switch is pressed during the cruise control driving, decrease vehicle set speed until the
switch is released. And then ASCD will keep the new set speed.
RESUME OPERATION
• When the ACCEL/RES switch is pressed after the cancel operation other than pressing ASCD MAIN switch
is performed, vehicle speed is return to last set speed. To resume vehicle set speed, vehicle condition must
meet following conditions.
- Brake pedal is released
- Selector lever is in other than P and N positions
- Vehicle speed is greater than 38 km/h (24 MPH) and less than 144 km/h (90 MPH)
EC-50
< SYSTEM DESCRIPTION >
[HR16DE]
ON BOARD DIAGNOSTIC (OBD) SYSTEM
ON BOARD DIAGNOSTIC (OBD) SYSTEM
Diagnosis Description
INFOID:0000000009267012
This system is an on board diagnostic system that records exhaust emission-related diagnostic information
and detects a sensors/actuator-related malfunction. A malfunction is indicated by the malfunction indicator
lamp (MIL) and stored in ECU memory as a DTC. The diagnostic information can be obtained with the diag-
nostic tool (GST: Generic Scan Tool).
GST (Generic Scan Tool)
INFOID:0000000009267013
When GST is connected with a data link connector equipped on the vehicle side, it will communicate with the
control unit equipped in the vehicle and then enable various kinds of diagnostic tests. Refer to
.
NOTE:
Service $0A is not applied for regions where it is not mandated.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст