Nissan Versa Sedan. Instruction — part 92
BR-6
< PREPARATION >
PREPARATION
Brake caliper wrench (front)
Return the piston
Power tool
Loosening nuts, screws and bolts
Tool name
Description
NNFIA0040ZZ
PIIB1407E
2014 Versa Sedan
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
BR-7
< SYMPTOM DIAGNOSIS >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000009267521
Use the chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×: Applicable
Reference page
,
,
,
,
,
(front
axle)
(rear axle)
(fro
nt
su
sp
en
si
on
)
(rea
r su
spe
n
si
on
)
(whe
el
an
d t
ire
)
(whe
el
an
d t
ire
)
(front
axle)
(s
te
eri
ng sy
st
em
)
Possible cause and
SUSPECTED PARTS
P
ad
s o
r li
ni
ng
da
ma
ge
d
P
ad
s o
r li
ni
ng
un
ev
en
wea
r
S
him
s da
ma
ge
d
Ro
to
r im
ba
lan
ce
Rot
o
r o
r dru
m
da
ma
ge
Rotor runout
Ro
to
r de
form
at
io
n
Ro
to
r or d
rum
d
efl
ectio
n
Ro
to
r or d
rum
ru
st
Rotor th
ic
kn
es
s va
ria
tio
n
Drum
o
u
t of
ro
un
d
A
XLE AND
SUSPENSI
ON
TI
RE
ROAD W
H
EEL
DRIV
E SHAFT
S
T
EERING
Symptom
BRAKE
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
Shimmy, Shudder
×
×
×
×
×
×
×
×
×
×
×
×
2014 Versa Sedan
BR-8
< PERIODIC MAINTENANCE >
BRAKE PEDAL
PERIODIC MAINTENANCE
BRAKE PEDAL
Inspection and Adjustment
INFOID:0000000009267522
INSPECTION
Brake Pedal Height
Check the height (H
1
) between the dash lower panel (1) and the
brake pedal upper surface.
CAUTION:
Remove the floor trim.
Stop Lamp Switch
Check the clearance (C) among the brake pedal lever (1) and the
stop lamp switch (2) threaded end.
CAUTION:
The stop lamp must turn off when the brake pedal is released.
ASCD Cancel Switch
Check the clearance (C) among the brake pedal lever (1) and the
ASCD cancel switch (2) threaded end.
CAUTION:
The stop lamp must turn off when the brake pedal is released.
Brake Pedal Play
Press the brake pedal. Check the brake pedal play (A) (stroke until
fluid pressure occurs).
Depressed Brake Pedal Height
(H
1)
: Refer to
.
JPFIA0065ZZ
(C)
: Refer to
JPFIA0866ZZ
(C)
: Refer to
.
JPFIA0866ZZ
(A)
: Refer to
JPFIA0277ZZ
2014 Versa Sedan
BRAKE PEDAL
BR-9
< PERIODIC MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
Check the height between the dash lower panel (1) and the brake
pedal upper surface (H
2
) when depressing the brake pedal at 490 N
(50 kg-f, 110 lb-f) while turning engine ON.
CAUTION:
Remove the floor trim.
ADJUSTMENT
Brake Pedal Height
1. Remove instrument lower panel LH. Refer to
IP-20, "Removal and Installation"
2. Disconnect the harness connector from stop lamp switch.
3. Loosen the stop lamp switch 45
° counterclockwise.
4. Adjust the brake pedal height with the following procedure.
a. Loosen the input rod lock nut (1).
CAUTION:
The threaded end of the input rod (2) must project to the
inner side (L) of the clevis (3).
b. Rotate the input rod, adjust the brake pedal to the specified
height (H
1
).
c. Tighten the lock nut. Refer to
.
5. Check the brake pedal play.
Stop Lamp Switch
1. Remove instrument lower panel LH. Refer to
IP-20, "Removal and Installation"
2. Disconnect the harness connector from stop lamp switch.
3. Loosen the stop lamp switch 45
° counterclockwise.
4. Press-fit the stop lamp switch (2) until the stop lamp switch hits
the brake pedal lever (1) 45
° clockwise while pulling the brake
pedal pad slightly.
CAUTION:
• The clearance (C) between the brake pedal lever and stop
lamp switch threaded and must be the specified value.
• The stop lamp must be turned off when the brake pedal is
released.
(H
2)
: Refer to
JPFIA0068ZZ
JPFIA0003ZZ
(H
1)
: Refer to
JPFIA0279ZZ
(C)
: Refer to
JPFIA0866ZZ
2014 Versa Sedan
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст