Nissan Versa Sedan. Instruction — part 751
ST-6
< BASIC INSPECTION >
STEERING WHEEL
Perform front wheel turning angle inspection, after toe-in inspection.
2. Place front wheels on turning radius gauges and rear wheels on
stands, so that vehicle can be level.
3. Check the maximum inner and outer wheel turning angles for LH
and RH road wheels.
• With the engine at idle, turn steering wheel from full left stop to
full right stop and measure the turning angles.
• Check the following items when turning angle is out of the standard.
- Check rack stroke (L).
- Disassemble steering gear assembly to check the cause that
rack stroke is outside of the standard.
• Steering angles are not adjustable. Check steering gear
assembly, steering column assembly and front suspension
components for wear or damage if any of the turning angles
are different from the specified value. Replace any of them, if
any non-standard condition exists.
FAA0016D
Inner wheel (Angle: A)
: Refer to
.
Outer wheel (Angle: B)
: Refer to
.
SGIA0055E
Rack stroke (L)
: Refer to
JSGIA0272ZZ
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
ST-7
< SYMPTOM DIAGNOSIS >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000009266809
Use the chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×: Applicable
Reference page
"
Possible cause and SUSPECTED PARTS
Ou
ter/
inn
er
so
ck
et
ba
ll
joi
nt
swi
ng
ing
to
rqu
e
O
u
ter/
inn
er
so
ck
et
ba
ll
joi
nt
rot
ati
ng
to
rque
O
u
ter/
inn
er
so
ck
et
ba
ll
joi
nt
en
d p
la
y
S
te
e
ring
whe
e
l pl
ay
Im
pro
p
er
st
ee
ring
wh
ee
l
Im
p
rop
er i
ns
tal
la
tio
n o
r lo
os
en
es
s of
til
t l
oc
k l
ev
er
M
ou
nt
ing
loos
e
nes
s
S
tee
rin
g c
o
lum
n
de
form
at
ion
o
r da
ma
ge
Im
p
rop
er i
ns
tal
la
tio
n o
r lo
os
en
es
s of
st
ee
ring
c
olu
m
n
S
te
eri
ng
li
nk
ag
e l
oo
se
ne
ss
A
XLE and
SUSP
ENSION
TI
RE
ROAD W
H
EEL
DRIV
E SHAFT
BR
AK
E
Symptom
Noise
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
Shudder
×
×
×
×
×
×
×
ST-8
< REMOVAL AND INSTALLATION >
STEERING WHEEL
REMOVAL AND INSTALLATION
STEERING WHEEL
Exploded View
INFOID:0000000009266810
Removal and Installation
INFOID:0000000009266811
REMOVAL
NOTE:
When reconnecting spiral cable, secure cable with a tape so that case and rotating part stay aligned. This will
omit neutral position alignment procedure during spiral cable installation.
1. Set vehicle to the straight-ahead position.
2. Remove driver air bag module. Refer to
SR-11, "Removal and Installation"
.
3. Remove steering wheel lock nut after steering is locked.
4. Remove steering wheel using a suitable tool (A).
INSTALLATION
Installation is in the reverse order of removal.
• Check the spiral cable neutral position after replacing or rotating spiral cable. Refer to
.
CAUTION:
• Do not twist spiral cable excessively after it becomes tight. (Twisting may cause the cable to be
torn off.)
• Do not reuse steering wheel lock nut.
1.
Steering wheel
JSGIA0704GB
JSGIA0654ZZ
STEERING COLUMN
ST-9
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
STEERING COLUMN
Exploded View
INFOID:0000000009266812
Removal and Installation
INFOID:0000000009266813
REMOVAL
CAUTION:
• Keep steering column assembly away from magnetic sources.
• Do not disassemble steering column assembly.
• While removing the steering column assembly, do not move the steering gear.
• When removing the steering column assembly, be careful not to allow the intermediate shaft to turn.
1. Set vehicle to the straight-ahead position.
2. Place the steering column tilt to the lowest selection.
3. Remove instrument lower panel LH. Refer to
IP-20, "Removal and Installation"
4. Remove driver air bag module. Refer to
SR-11, "Removal and Installation"
.
5. Remove steering wheel. Refer to
6. Remove steering column covers. Refer to
IP-15, "Removal and Installation"
.
7. Remove spiral cable. Refer to
SR-14, "Removal and Installation"
.
8. Remove combination switch. Refer to
9. Remove the cluster lid A. Refer to
IP-19, "Removal and Installation"
10. Disconnect the harness connectors from the steering switch.
11. Remove the key cylinder only if the steering column is being replaced. Refer to
.
12. Place the steering column tilt to the middle selection.
CAUTION:
Do not change the position of the tilt mechanism until the steerign column is reinstalled.
13. Loosen the steering shaft lower joint bolt.
14. Remove the intermediate shaft upper bolt and separate intermediate shaft from steering column assem-
bly. Refer to
ST-12, "Removal and Installation"
.
CAUTION:
• Place a matching mark on both intermediate shaft and steering column assembly before remov-
ing intermediate shaft.
1.
Steering column assembly
2.
Clamp
JPGIA0110GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст