Nissan Versa Sedan. Instruction — part 588
MWI
THE OIL PRESSURE WARNING LAMP DOES NOT TURN OFF
MWI-51
< SYMPTOM DIAGNOSIS >
[TYPE A]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE OIL PRESSURE WARNING LAMP DOES NOT TURN OFF
Description
INFOID:0000000009266614
The oil pressure warning lamp remains on while the engine is running (normal oil pressure).
Diagnosis Procedure
INFOID:0000000009266615
1.
CHECK COMBINATION METER INPUT SIGNAL
1. Start the engine and select METER/M&A on CONSULT.
2. Observe OIL W/L DATA MONITOR and the operation of the oil pressure warning lamp on the combination
meter.
Is the inspection result normal?
YES
>> Perform ECM self-diagnosis. Refer to
.
NO
>> Replace combination meter. Refer to
MWI-53, "Removal and Installation"
Component
Condition
CONSULT
Oil pressure warning light
Engine running
OFF
MWI-52
< SYMPTOM DIAGNOSIS >
[TYPE A]
THE LOW WASHER FLUID WARNING CONTINUES DISPLAYING, OR DOES
NOT DISPLAY
THE LOW WASHER FLUID WARNING CONTINUES DISPLAYING, OR
DOES NOT DISPLAY
Description
INFOID:0000000009266616
• The warning is still displayed even after washer fluid is added.
• The warning is not displayed even though the washer tank is empty.
Diagnosis Procedure
INFOID:0000000009266617
1.
CHECK WASHER FLUID LEVEL SWITCH
Perform a unit check for the washer fluid level switch. Refer to
MWI-48, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace washer fluid level switch. Refer to
.
2.
CHECK WASHER FLUID LEVEL SWITCH SIGNAL CIRCUIT
Check the washer fluid level switch signal circuit. Refer to
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-53, "Removal and Installation"
NO
>> Repair or replace harness or connector.
MWI
COMBINATION METER
MWI-53
< REMOVAL AND INSTALLATION >
[TYPE A]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
REMOVAL AND INSTALLATION
COMBINATION METER
Removal and Installation
INFOID:0000000009266618
REMOVAL
1. Disconnect the negative battery terminal. Refer to
PG-63, "Removal and Installation"
2. Remove cluster lid A. Refer to
IP-19, "Removal and Installation"
3. Remove the combination meter screws.
4. Pull the combination meter straight out to disengage resin clips.
NOTE:
The illustration shows the clip positions on the back of the com-
bination meter.
5. Disconnect the harness connector from the combination meter and remove.
INSTALLATION
Installation is in the reverse order of removal.
JSNIA3895ZZ
MWI-54
< UNIT DISASSEMBLY AND ASSEMBLY >
[TYPE A]
COMBINATION METER
UNIT DISASSEMBLY AND ASSEMBLY
COMBINATION METER
Exploded View
INFOID:0000000009266619
Disassembly and Assembly
INFOID:0000000009266620
DISASSEMBLY
1. Disengage the tabs to separate front cover using a suitable tool.
2. Pull the front cover straight out to remove from the unified meter control unit.
CAUTION:
• Do not touch the display, pointer, the inside of front cover and the printed area of the dial during
the work.
• Keep away from magnetic sources.
• Do not damage the front cover.
ASSEMBLY
Assembly is in the reverse order of disassembly.
CAUTION:
• Do not touch the display, pointer, the inside of front cover and the printed area of the dial during the
work.
• Keep away from magnetic sources.
• Do not damage the front cover.
1.
Unified meter control unit
2.
Front cover
JSNIA2929ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст