Nissan Versa Sedan. Instruction — part 513

INL-48

< DTC/CIRCUIT DIAGNOSIS >

PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT

YES

>> GO TO 3.

NO

>> Repair or replace the harness or connectors.

3.

CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION POWER SUPPLY SHORT CIRCUIT

Check continuity between BCM connector M98 terminal 90 and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to

BCS-69, "Removal and Installation"

.

NO

>> Repair or replace the harness or connectors.

4.

CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION GROUND CIRCUIT

1. Turn the ignition switch OFF

2. Disconnect push-button ignition switch connector.

3. Check continuity between push-button ignition switch connector M25 terminal 6 and ground.

Is the inspection result normal?

YES

>> Replace push-button ignition switch. Refer to

PCS-100, "Removal and Installation"

.

NO

>> GO TO 5.

5.

CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION GROUND OPEN CIRCUIT

1. Disconnect BCM connector M98.

2. Check continuity between BCM connector M98 terminal 92 and push-button ignition switch connector

M25 terminal 6.

Is the inspection result normal?

YES

>> Replace BCM. Refer to

BCS-69, "Removal and Installation"

.

NO

>> Repair or replace the harness or connectors.

BCM

Ground

Continuity

Connector

Terminal

M98

90

No

Push-button ignition switch

Ground

Continuity

Connector

Terminal

M25

6

Yes

BCM

Push-button ignition switch

Continuity

Connector

Terminal

Connector

Terminal

M98

92

M25

6

Yes

INTERIOR LIGHTING SYSTEM SYMPTOMS

INL-49

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

INL

N

O

P

SYMPTOM DIAGNOSIS

INTERIOR LIGHTING SYSTEM SYMPTOMS

Symptom Table

INFOID:0000000009269258

CAUTION:

Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagno-

sis if any DTC is detected.

Symptom

Possible cause

Inspection item

• Interior room lamp does not turn ON even though the

door is open.
(It turns ON when turning the interior room lamp ON.)

• Interior room lamp does not turn OFF even though

the door is closed.

• Harness between BCM and each

door switch

• Harness between BCM and each

interior room lamp

• BCM

Door switch circuit
Refer to

DLK-89

(with Intelligent Key)

or

DLK-235

(without Intelligent Key).

Interior room lamp control circuit
Refer to

INL-43

.

Interior room lamp timer does not activate.
(It turns ON/ OFF when the door opens/closes.)

—

Check the interior room lamp setting.
Refer to

BCS-17

(with Intelligent Key)

or

BCS-83

(without Intelligent Key).

Interior room lamp battery saver does not activate.

—

Check the interior room lamp battery
saver setting.
Refer to

BCS-24

(with Intelligent Key)

or

BCS-89

(without Intelligent Key).

Trunk room lamp does not turn ON even though the
trunk lid is open.
(It turns ON when turning the trunk room lamp ON.)

• Harness between BCM and trunk

room lamp

• Harness between BCM and trunk

lid switch

• BCM

Trunk lid switch circuit
Refer to

DLK-103

(with Intelligent Key)

or

BCS-89

(without Intelligent Key).

Trunk room lamp circuit
Refer to

INL-45

.

INL-50

< REMOVAL AND INSTALLATION >

MAP LAMP

REMOVAL AND INSTALLATION

MAP LAMP

Exploded View

INFOID:0000000009269259

Removal and Installation

INFOID:0000000009269260

WARNING:

Do not touch bulb with your hand while it is on or right after being turned off. Burning may result.

CAUTION:

Do not touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to prevent

damage to the bulb.

REMOVAL

1. Release lens pawls using suitable tool (A) and remove.

CAUTION:

Apply protect tape (B) on suitable tool (A).

: Pawl

2. Release map lamp housing pawl using suitable tool (A).

CAUTION:

Apply protect tape (B) on suitable tool (A).

: Pawl

3. Disconnect the harness connector from map lamp and remove.

1.

Map lamp bulb housing

2.

Bulb

3.

Lens

Pawl

JMLIA1062ZZ

AWLIA1898ZZ

AWLIA1899ZZ

MAP LAMP

INL-51

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

INL

N

O

P

INSTALLATION

Installation is in the reverse order of removal.

Bulb Replacement

INFOID:0000000009269261

WARNING:

Do not touch bulb with your hand while it is on or right after being turned off. Burning may result.

CAUTION:

• Do not touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-

vent damage to the bulb.

• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the

lens and reflector (causing dirt or clouding). Always prepare a new bulb and have it on hand when

replacing the bulb.

MAP LAMP BULB

Removal

1. Release lens pawls using suitable tool (A) and remove.

CAUTION:

Apply protect tape (B) on suitable tool (A).

: Pawl

2. Remove the bulb.

Installation

Installation is in the reverse order of removal.

AWLIA1898ZZ