Nissan Altima L32. Instruction — part 580
P2101 ELECTRIC THROTTLE CONTROL FUNCTION
EC-1441
< COMPONENT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
3. Disconnect ECM harness connector.
4. Check the continuity between electric throttle control actuator harness connector and ECM harness con-
nector.
5. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair or replace malfunctioning part.
8.
CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY
1. Remove the intake air duct.
2. Check if foreign matter is caught between the throttle valve (1)
and the housing.
-
Electric throttle control actuator (2)
-
: Vehicle front
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Remove the foreign matter and clean the electric throttle
control actuator inside.
9.
CHECK THROTTLE CONTROL MOTOR
EC-1441, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> GO TO 11.
10.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Repair or replace harness or connectors.
11.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1. Replace electric throttle control actuator.
2. Refer to
EC-1442, "Special Repair Requirement"
.
>> INSPECTION END
Component Inspection
INFOID:0000000004362310
1.
CHECK THROTTLE CONTROL MOTOR
1. Turn ignition switch OFF.
2. Disconnect electric throttle control actuator harness connector.
Electric throttle control actuator
ECM
Continuity
Connector
Terminal
Connector
Terminal
F57
5
F14
5
Not existed
6
Existed
6
5
Existed
6
Not existed
ALBIA0124ZZ
EC-1442
< COMPONENT DIAGNOSIS >
[VQ35DE]
P2101 ELECTRIC THROTTLE CONTROL FUNCTION
3. Check resistance between electric throttle control actuator termi-
nals as per the following.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1. Replace electric throttle control actuator.
2. Go to
EC-1442, "Special Repair Requirement"
>> INSPECTION END
Special Repair Requirement
INFOID:0000000004362311
1.
PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
EC-1053, "THROTTLE VALVE CLOSED POSITION LEARNING : Special Repair Requirement"
>> GO TO 2.
2.
PERFORM IDLE AIR VOLUME LEARNING
EC-1053, "IDLE AIR VOLUME LEARNING : Special Repair Requirement"
>> END
Terminals
Resistance
5 and 6
Approx. 1 - 15
Ω [at 25°C (77°F)]
PBIB2909E
P2118 THROTTLE CONTROL MOTOR
EC-1443
< COMPONENT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P2118 THROTTLE CONTROL MOTOR
Description
INFOID:0000000004362312
The throttle control motor is operated by the ECM and it opens and closes the throttle valve.
The current opening angle of the throttle valve is detected by the throttle position sensor. The throttle position
sensor it provides feedback to the ECM, when opens/closes the throttle valve in response to driving conditions
via the throttle control motor.
DTC Logic
INFOID:0000000004362313
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON and wait at least 2 seconds.
2. Start engine and let it idle for 5 seconds.
3. Check DTC.
Is DTC detected?
YES
>> Go to
EC-1443, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000004362314
1.
CHECK GROUND CONNECTION
1. Turn ignition switch OFF.
2. Check ground connection E9. Refer to Ground Inspection in
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace ground connection.
2.
CHECK THROTTLE CONTROL MOTOR OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Disconnect electric throttle control actuator harness connector.
2. Disconnect ECM harness connector.
3. Check the continuity between electric throttle control actuator harness connector and ECM harness con-
nector.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P2118
Throttle control motor
circuit short
ECM detects short in both circuits between
ECM and throttle control motor.
• Harness or connectors
(Throttle control motor circuit is shorted.)
• Electric throttle control actuator
(Throttle control motor)
EC-1444
< COMPONENT DIAGNOSIS >
[VQ35DE]
P2118 THROTTLE CONTROL MOTOR
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning part.
3.
CHECK THROTTLE CONTROL MOTOR
EC-1444, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 5.
4.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness or connectors.
5.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1. Replace electric throttle control actuator.
2. Go to
EC-1445, "Special Repair Requirement"
>> INSPECTION END
Component Inspection
INFOID:0000000004362315
1.
CHECK THROTTLE CONTROL MOTOR
1. Turn ignition switch OFF.
2. Disconnect electric throttle control actuator harness connector.
3. Check resistance between electric throttle control actuator termi-
nals as per the following.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1. Replace electric throttle control actuator.
2. Go to
EC-1442, "Special Repair Requirement"
>> INSPECTION END
Electric throttle control actuator
ECM
Continuity
Connector
Terminal
Connector
Terminal
F57
5
F14
5
Not existed
6
Existed
6
5
Existed
6
Not existed
Terminals
Resistance
5 and 6
Approx. 1 - 15
Ω [at 25°C (77°F)]
PBIB2909E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст