Nissan Altima L32. Instruction — part 236
AIR CONDITIONING CUT CONTROL
EC-65
< FUNCTION DIAGNOSIS >
[QR25DE FOR CALIFORNIA]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Component Description
INFOID:0000000004349158
1.
No.1 ignition coil
2.
Cooling fan motor-1 harness con-
nector
3.
Cooling fan motor-2 harness con-
nector
4.
Refrigerant pressure sensor
5.
Accelerator pedal position sensor
6.
ASCD brake switch
7.
Stop lamp switch
8.
Brake pedal
9.
ASCD clutch switch
10. Clutch pedal
11. ASCD steering switch
12. CANSEC switch
13. RESUME/ACCELERATE switch
14. SET/COAST switch
15. MAIN switch
: Vehicle front
ALBIA0089ZZ
Component
Reference
Accelerator pedal position sensor
Camshaft position sensor (PHASE)
Crankshaft position sensor (POS)
Engine coolant temperature sensor
EC-66
< FUNCTION DIAGNOSIS >
[QR25DE FOR CALIFORNIA]
AIR CONDITIONING CUT CONTROL
Power steering pressure sensor
Refrigerant pressure sensor
Vehicle speed sensor
Component
Reference
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
EC-67
< FUNCTION DIAGNOSIS >
[QR25DE FOR CALIFORNIA]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
System Diagram
INFOID:0000000004349159
System Description
INFOID:0000000004349160
INPUT/OUTPUT SIGNAL CHART
*: This signal is sent to the ECM through CAN communication line
BASIC ASCD SYSTEM
Refer to Owner's Instruction for ASCD operating instructions.
Automatic Speed Control Device (ASCD) allows a driver to keep vehicle at predetermined constant speed
without depressing accelerator pedal. Driver can set vehicle speed in advance between approximately 40 km/
h (25 MPH) and 144 km/h (89 MPH).
ECM controls throttle angle of electric throttle control actuator to regulate engine speed.
The ASCD operation status is indicated by two indicators (CRUISE and SET on the information display) on the
combination meter. If any malfunction occurs in ASCD system, SET indicator blinks and ASCD control is deac-
tivated.
NOTE:
Always drive vehicle in safe manner according to traffic conditions and obey all traffic laws.
SET OPERATION
Press MAIN switch. (CRUISE is indicated on the information display.)
When vehicle speed reaches a desired speed between approximately 40 km/h (25 MPH) and 144 km/h (89
MPH), press SET/COAST switch. (Then SET is indicated on the information display.)
ACCELERATE OPERATION
If the RESUME/ACCELERATE switch is pressed during cruise control driving, increase the vehicle speed until
the switch is released or vehicle speed reaches maximum speed controlled by the system.
And then ASCD will keep the new set speed.
JMBIA0176GB
Sensor
Input signal to ECM
ECM function
Actuator
ASCD brake switch
Brake pedal operation
ASCD vehicle speed control
Electric throttle control
actuator
Stop lamp switch
Brake pedal operation
ASCD clutch switch (M/T models)
Clutch pedal operation
ASCD steering switch
ASCD steering switch operation
Park/neutral position (PNP) switch Gear position
Combination meter
Vehicle speed*
TCM (CVT models)
Powertrain revolution*
EC-68
< FUNCTION DIAGNOSIS >
[QR25DE FOR CALIFORNIA]
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
CANCEL OPERATION
When any of following conditions exist, cruise operation will be canceled.
• CANCEL switch is pressed
• More than 2 switches at ASCD steering switch are pressed at the same time (Set speed will be cleared)
• Brake pedal is depressed
• Clutch pedal is depressed or gear position is changed to neutral position. (M/T models)
• Selector lever is changed to N, P, R position (CVT models)
• Vehicle speed decreased to 13 km/h (8 MPH) lower than the set speed
• TCS system is operated
When the ECM detects any of the following conditions, the ECM will cancel the cruise operation and inform
the driver by blinking indicators.
• Engine coolant temperature is slightly higher than the normal operating temperature, CRUISE indicator may
blink slowly.
When the engine coolant temperature decreases to the normal operating temperature, CRUISE indicator will
stop blinking and the cruise operation will be able to work by pressing SET/COAST switch or RESUME/
ACCELERATE switch.
• Malfunction for some self-diagnoses regarding ASCD control: SET indicator will blink quickly.
If MAIN switch is turned to OFF during ASCD is activated, all of ASCD operations will be canceled and vehicle
speed memory will be erased.
COAST OPERATION
When the SET/COAST switch is pressed during cruise control driving, decrease vehicle set speed until the
switch is released. And then ASCD will keep the new set speed.
RESUME OPERATION
When the RESUME/ACCELERATE switch is pressed after cancel operation other than pressing MAIN switch
is performed, vehicle speed will return to last set speed. To resume vehicle set speed, vehicle condition must
meet following conditions.
• Brake pedal is released
• Clutch pedal is released (M/T models)
• Selector lever is in other than P and N positions (CVT models)
• Vehicle speed is greater than 40 km/h (25 MPH) and less than 144 km/h (89 MPH)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст