Nissan Altima L32. Instruction — part 441
P1550 BATTERY CURRENT SENSOR
EC-885
< COMPONENT DIAGNOSIS >
[QR25DE EXCEPT FOR CALIFORNIA]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
3. Check the voltage between battery current sensor harness con-
nector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair open circuit or sort to ground or short to power in
harness or connectors.
3.
CHECK BATTERY CURRENT SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between battery current sensor harness connector and ECM harness connector.
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair open circuit or sort to ground or short to power in harness or connectors.
4.
CHECK BATTERY CURRENT SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Check the continuity between battery current sensor harness connector and ECM harness connector.
2. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair open circuit or sort to ground or short to power in harness or connectors.
5.
CHECK BATTERY CURRENT SENSOR
EC-885, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace battery negative cable assembly.
6.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000004349858
1.
CHECK BATTERY CURRENT SENSOR
1. Reconnect harness connectors disconnected.
Battery current sensor
Ground
Voltage
Connector
Terminal
F5
1
Ground
Approx. 5V
JMBIA1602ZZ
Battery current sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F5
2
F13
44
Existed
Battery current sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F5
3
F13
42
Existed
EC-886
< COMPONENT DIAGNOSIS >
[QR25DE EXCEPT FOR CALIFORNIA]
P1550 BATTERY CURRENT SENSOR
2. Disconnect battery negative cable (1).
3. Install jumper cable (A) between battery negative terminal and
body ground.
4. Turn ignition switch ON.
5. Check the voltage between ECM harness connector and
ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace battery negative cable assembly.
: To body ground
ALBIA0076ZZ
ECM
Ground
Voltage
Connector
Terminal
F13
42
(Battery current sensor signal)
Ground Approx. 2.5V
JMBIA1603ZZ
P1551, P1552 BATTERY CURRENT SENSOR
EC-887
< COMPONENT DIAGNOSIS >
[QR25DE EXCEPT FOR CALIFORNIA]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P1551, P1552 BATTERY CURRENT SENSOR
Description
INFOID:0000000004349859
The power generation voltage variable control enables fuel consumption to be decreased by reducing the
engine load which is caused by the power generation of the generator. The battery current sensor is installed
to the battery cable at the negative terminal. The sensor measures the charging/discharging current of the bat-
tery. Based on the sensor signal, ECM judges whether or not the power generation voltage variable control is
performed. When performing the power generation voltage variable control, ECM calculates the target power
generation voltage based on the sensor signal. And ECM sends the calculated value as the power generation
command value to IPDM E/R. For the details of the power generation voltage variable control, refer to
CAUTION:
Do not connect the electrical component or the ground wire directly to the battery terminal. The con-
nection causes the malfunction of the power generation voltage variable control, and then the battery
discharge may occur.
DTC Logic
INFOID:0000000004349860
DTC DETECTION LOGIC
NOTE:
If DTC P1551 or P1552 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.
Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8V with ignition
switch ON
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON wait at least 10 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000004349861
1.
CHECK GROUND CONNECTION
1. Turn ignition switch OFF.
2. Check ground connection E9. Refer to Ground Inspection in
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace ground connection.
2.
CHECK BATTERY CURRENT SENSOR POWER SUPPLY CIRCUIT
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1551
Battery current sensor circuit
low input
An excessively low voltage from the sen-
sor is sent to ECM.
• Harness or connectors
(The sensor circuit is open or shorted.)
• Battery current sensor
P1552
Battery current sensor circuit
high input
An excessively high voltage from the sen-
sor is sent to ECM.
EC-888
< COMPONENT DIAGNOSIS >
[QR25DE EXCEPT FOR CALIFORNIA]
P1551, P1552 BATTERY CURRENT SENSOR
1. Disconnect battery current sensor harness connector.
2. Turn ignition switch ON.
3. Check the voltage between battery current sensor harness con-
nector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair open circuit or sort to ground or short to power in
harness or connectors.
3.
CHECK BATTERY CURRENT SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between battery current sensor harness connector and ECM harness connector.
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair open circuit or sort to ground or short to power in harness or connectors.
4.
CHECK BATTERY CURRENT SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Check the continuity between battery current sensor harness connector and ECM harness connector.
2. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair open circuit or sort to ground or short to power in harness or connectors.
5.
CHECK BATTERY CURRENT SENSOR
EC-888, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace battery negative cable assembly.
6.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000004349862
1.
CHECK BATTERY CURRENT SENSOR
1. Reconnect harness connectors disconnected.
Battery current sensor
Ground
Voltage
Connector
Terminal
F5
1
Ground
Approx. 5V
JMBIA1602ZZ
Battery current sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F5
2
F13
44
Existed
Battery current sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F5
3
F13
42
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст