Nissan Altima L32. Instruction — part 949
MWI-48
< COMPONENT DIAGNOSIS >
OIL PRESSURE SWITCH SIGNAL CIRCUIT
OIL PRESSURE SWITCH SIGNAL CIRCUIT
Description
INFOID:0000000004204098
Detects the engine oil pressure and transmits the oil pressure switch signal to the IPDM E/R.
Component Function Check
INFOID:0000000004204099
1.
COMBINATION METER INPUT SIGNAL
1. Select “METER/M&A” on CONSULT-III.
2. Monitor “OIL W/L” of “DATA MONITOR” while operating ignition switch.
>> Inspection End.
Diagnosis Procedure
INFOID:0000000004204100
1.
CHECK OIL PRESSURE SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector F10 and oil pressure switch
connector F41.
3. Check continuity between IPDM E/R harness connector F10 (A)
terminal 75 and oil pressure switch harness connector F41 (B)
terminal 1.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair harness or connector.
Component Inspection
INFOID:0000000004204101
1.
CHECK OIL PRESSURE SWITCH
Check continuity between oil pressure switch and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace the oil pressure switch.
OIL W/L
When ignition switch is in ON
position (Engine stopped)
: ON
When engine is running
: OFF
Continuity should exist.
AWNIA0016ZZ
Condition
Oil pressure [kPa (kg/cm
2
, psi)]
Continuity
Engine stopped
Less than 29 (0.3, 4)
Yes
Engine running
More than 29 (0.3, 4)
No
ELF0044D
MWI
PARKING BRAKE SWITCH SIGNAL CIRCUIT
MWI-49
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
PARKING BRAKE SWITCH SIGNAL CIRCUIT
Description
INFOID:0000000004204102
Transmits the parking brake switch signal to the combination meter.
Component Function Check
INFOID:0000000004204103
1.
COMBINATION METER INPUT SIGNAL
1. Select “METER/M&A” on CONSULT-III.
2. Monitor “PKB SW” of “DATA MONITOR” while applying and releasing the parking brake.
>> Inspection End.
Diagnosis Procedure
INFOID:0000000004204104
COUPE
1.
CHECK PARKING BRAKE SWITCH CIRCUIT
1. Disconnect combination meter connector and parking brake
switch connector.
2. Check continuity between combination meter harness connector
M24 (A) terminal 26 and parking brake switch harness connec-
tor M73 (B) terminal 1.
3. Check continuity between combination meter harness connector
M24 (A) terminal 26 and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair harness or connector.
SEDAN
1.
CHECK PARKING BRAKE SWITCH CIRCUIT
1. Disconnect combination meter connector and parking brake
switch connector.
2. Check continuity between combination meter harness connector
M24 (A) terminal 26 and parking brake switch harness connec-
tor M73 (B) (with M/T) or E35 (B) (with CVT) terminal 1.
3. Check continuity between combination meter harness connector
M24 (A) terminal 26 and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair harness or connector.
PKB SW
Parking brake applied
: ON
Parking brake released
: OFF
26 - 1
: Continuity should exist.
26 - Ground
: Continuity should not exist.
AWNIA0017ZZ
26 - 1
: Continuity should exist.
26 - Ground
: Continuity should not exist.
AWNIA0017ZZ
MWI-50
< COMPONENT DIAGNOSIS >
PARKING BRAKE SWITCH SIGNAL CIRCUIT
Component Inspection
INFOID:0000000004204105
1.
CHECK PARKING BRAKE SWITCH
Check continuity between parking brake switch terminal 1 and switch
case ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace parking brake switch.
Component
Terminal
Condition
Continuity
Parking brake switch
1
Parking brake applied
Yes
Parking brake released
No
AWNIA0018ZZ
MWI
WASHER LEVEL SWITCH SIGNAL CIRCUIT
MWI-51
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
WASHER LEVEL SWITCH SIGNAL CIRCUIT
Description
INFOID:0000000004204106
Transmits the washer level switch signal to the combination meter.
Component Function Check
INFOID:0000000004204107
1.
COMBINATION METER INPUT SIGNAL
1. Select “METER/M&A” on CONSULT-III.
2. Monitor “WASHER W/L” of “DATA MONITOR” under the following conditions.
>> Inspection End.
Diagnosis Procedure
INFOID:0000000004204108
1.
CHECK WASHER LEVEL SWITCH SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector and washer level
switch connector.
3. Check continuity between combination meter harness connector
M24 (A) terminal 29 and washer level switch harness connector
E208 (B) terminal 1.
4. Check continuity between combination meter harness connector
M24 (A) terminal 29 and ground.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Repair harness or connector.
2.
CHECK WASHER LEVEL SWITCH GROUND CIRCUIT
Check continuity between washer fluid level switch harness connec-
tor E208 terminal 2 and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair harness or connector.
Component Inspection
INFOID:0000000004204109
1.
CHECK WASHER FLUID LEVEL SWITCH
WASHER W/L
Washer fluid level low
: ON
Washer fluid level other : OFF
29 - 1
: Continuity should exist.
29 - Ground
: Continuity should not exist.
AWNIA0311ZZ
2 - Ground
: Continuity should exist.
AWNIA0312ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст