Nissan Altima L32. Instruction — part 155
BRM-10
< ON-VEHICLE REPAIR >
[COUPE]
BODY COMPONENT PARTS
Body Component Parts
INFOID:0000000004205847
1.
Roof panel assembly
2.
Rear roof rail assembly
3.
Center roof bow
4.
Front roof bow
5.
Front roof rail assembly
6.
Sun roof panel assembly
7.
Front pillar inner reinforcement (RH,
LH)
8.
Inner lock pillar (RH, LH)
9.
Outer upper roof side rail (RH, LH)
ALKIA0793GB
BODY COMPONENT PARTS
BRM-11
< ON-VEHICLE REPAIR >
[COUPE]
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
10. Hinge pillar upper reinforcement
(RH, LH)
11. Lock pillar reinforcement (RH, LH)
12. Outer sill reinforcement (RH, LH)
13. Hinge pillar lower reinforcement
(RH, LH)
14. Front pillar lower reinforcement (RH,
LH)
15. Hood assembly
16. Front fender (RH, LH)
17. Front portion of body side outer (RH,
LH)
18. Rear fender portion of body side out-
er (RH, LH)
19. Body side outer (RH, LH)
20. Front door outer (RH, LH)
21. Front door assembly (RH, LH)
22. Rear combination lamp base (RH,
LH)
23. Rear outer sill reinforcement (RH,
LH)
24. Rear wheel outer front extension
(RH, LH)
25. Rear wheel outer RH, LH)
26. Rear pillar inner reinforcement B
(RH, LH)
27. Rear pillar inner reinforcement A
(RH, LH)
28. Inner rear pillar lower (RH, LH)
29. Rear pillar inner (RH, LH)
30. Rear seat back side support (RH,
LH)
31. Rear side upper reinforcement (RH,
LH)
32. Rear wheel inner reinforcement as-
sembly (RH, LH)
33. Rear bumper fascia brackets
34. Rear panel assembly
35. Parcel shelf assembly
36. Trunk lid assembly
BRM-12
< ON-VEHICLE REPAIR >
[COUPE]
CORROSION PROTECTION
CORROSION PROTECTION
Description
INFOID:0000000004205848
To provide improved corrosion prevention, the following anti-corrosive measures have been implemented in
NISSAN production plants. When repairing or replacing body panels, it is necessary to use the same anti-cor-
rosive measures.
Anti-Corrosive Precoated Steel (Galvannealed Steel)
To improve repairability and corrosion resistance, a new type of anti-
corrosive precoated steel sheet has been adopted replacing conven-
tional zinc-coated steel sheet.
Galvannealed steel is electroplated and heated to form Zinc-iron
alloy, which provides excellent and long term corrosion resistance
with cationic electrodeposition primer.
Nissan Genuine Service Parts are fabricated from galvannealed steel. Therefore, it is recommended that
GENUINE NISSAN PARTS or equivalent be used for panel replacement to maintain the anti-corrosive perfor-
mance built into the vehicle at the factory.
Phosphate Coating Treatment and Cationic Electrodeposition Primer
A phosphate coating treatment and a cationic electrodeposition primer, which provide excellent corrosion pro-
tection, are employed on all body components.
CAUTION:
Confine paint removal during welding operations to an absolute
minimum.
Nissan Genuine Service Parts are also treated in the same manner. Therefore, it is recommended that GENU-
INE NISSAN PARTS or equivalent be used for panel replacement to maintain anti-corrosive performance built
into the vehicle at the factory.
Anti-Corrosive Wax
INFOID:0000000004205849
To improve corrosion resistance, anti-corrosive wax is applied inside the body sill and inside other closed sec-
tions. Accordingly, when replacing these parts, be sure to apply anti-corrosive wax to the appropriate areas of
SIIA2294E
PIIA0095E
CORROSION PROTECTION
BRM-13
< ON-VEHICLE REPAIR >
[COUPE]
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
the new parts. Select an excellent anti-corrosive wax which will penetrate after application and has a long shelf
life.
Undercoating
INFOID:0000000004205850
The underside of the floor and wheelhouse are undercoated to prevent rust, vibration, noise and stone chip-
ping. Therefore, when such a panel is replaced or repaired, apply undercoating to that part. Use an undercoat-
ing which is rust preventive, soundproof, vibration-proof, shock-resistant, adhesive, and durable.
Precautions in Undercoating
1. Do not apply undercoating to any place unless specified (such as the areas above the muffler and three
way catalyst which are subjected to heat).
2. Do not undercoat the exhaust pipe or other parts which become hot.
3. Do not undercoat rotating parts.
4. Apply bitumen wax after applying undercoating.
ALKIA0794GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст